ENTRY AND START SYSTEM (for Entry Function) > OPERATION CHECK |
| CHECK ENTRY AND START SYSTEM (for Entry Function) OPERATION |
Check the entry unlock function (driver side door, front passenger side door).
Perform a wireless lock operation to lock all the doors, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver side door while carrying the electrical key transmitter and check that all the doors unlock.
![]() |
Inspect the entry unlock detection area. Hold the electrical key transmitter at the same height as the front door outside handle assembly (approximately 0.8 m (2.62 ft.) from the ground) and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
With the system in unlock standby mode, hold the front door outside handle assembly and check that all the doors unlock.
![]() |
Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.
| *1 | Unlock Sensor (Backside) |
Check the entry lock function (driver side door, front passenger side door).
![]() |
With all the doors closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver side door while carrying the electrical key transmitter sub-assembly and check that all the doors lock.
| *a | Approximately 0.3 m (0.98 ft.) |
![]() |
Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.1 m (0.33 ft.) below the bottom edge of the door glass (approximately 0.8 m (2.62 ft.) from the ground) and approximately 0.3 m (0.98 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that all the doors lock.
| *1 | Lock Sensor |
Check the entry luggage compartment open function.
![]() |
Perform a wireless lock operation to lock the doors, operate the unlock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly and check that the door unlocks.
| *1 | Unlock Switch |
| *a | Approximately 0.7 m (2.30 ft.) |
Inspect the entry luggage compartment door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the above illustration at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the unlock switch of the back door opener switch assembly and check that the luggage compartment door open.
Check the key lock-in prevention function (in luggage compartment).
Place the electrical key transmitter sub-assembly in the luggage compartment with all doors locked. Check that: 1) closing the luggage compartment door triggers the key wireless buzzer (which lasts approximately 2 seconds), and 2) pressing the back door opener switch assembly opens the luggage compartment door.
![]() |
Inspect the key lock-in prevention detection area. Pay attention to the direction of the electrical key transmitter sub-assembly shown in the illustration. When the electrical key transmitter sub-assembly is in either of the 2 locations in the illustration, check that: 1) closing the luggage compartment door sounds the wireless buzzer, and 2) pressing the back door opener switch assembly.
| *a | Inspection Point |
![]() |
Inspect the key lock-in prevention detection area and the door control receiver for wave leaks. Hold the electrical key transmitter sub-assembly at the same height as the lower edge of the luggage compartment door aligning it with the center of the rear of the vehicle. Pay attention to the direction and position of the electrical key transmitter sub-assembly shown in the illustration.
| *a | 0.1 m or more (0.328 ft. or more) |
Check the push start function (for Automatic Transmission).
With the engine switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly and check that the entry key indicator light in the combination meter assembly illuminates green. Then, with the entry key indicator light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.
With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off. However, if the shift lever is in any position other than P while the engine switch is on (IG), the power source mode will not change to off, but to on (ACC).
Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). However, if the shift lever is in any position other than P, even if the engine switch is pressed while the vehicle is stationary, the power source mode will not change to off, but to on (ACC). Move the shift lever to P, open the door and check that the steering lock operates.
![]() |
Inspect the entry ignition operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
| *a | Inspection Point |
![]() |
Inspect the push start operating range (inside luggage). Place the electrical key transmitter sub-assembly at either inspection point and check that the engine can be started.
| *a | Inspection Point |
Check the push start function (for Manual Transmission).
With the engine switch off, depress the clutch pedal while carrying the electrical key transmitter sub-assembly and check that the entry key indicator light in the combination meter assembly illuminates green. Then, with the entry key indicator light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.
With the clutch pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.
Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). Open the door and check that the steering lock operates.
![]() |
Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
| *a | Inspection Point |
![]() |
Inspect the push start operating range (inside luggage). Place the electrical key transmitter sub-assembly at either inspection point and check that the engine can be started.
| *a | Inspection Point |
Check the key lock-in prevention function (vehicle interior).
Turn the engine switch off.
Place the electrical key transmitter sub-assembly on a front or rear seat.
Close all the doors, but make sure all the doors are unlocked.
Touch a front door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.
Check the entry cancel function.
Cancel the entry and start system and check that all the functions of the entry and start system (for entry function) no longer operate.
While the key cancel function (entry cancel function) is on, check that all functions of the entry and start system cannot be operated.
Check the answer-back function (hazard warning light flashing and buzzer sounding*).
| Entry Operation | Wireless Buzzer* | Hazard Warning Light |
| Entry Door Lock | Sounds once* | Flashes once |
| Entry Door Unlock | Sounds twice* | Flashes twice |
| Entry Luggage Compartment Open | Does not sound* | Does not flash |
| KEY DIAGNOSTIC MODE (Using GTS) |
Enter the following menus: Body Electrical / Entry & Start / Utility / Communication Check (Key Diag Mode).
Inspect the appropriate item according to the following table.
| Tester Display | Inspection Item |
| Overhead + Driver Side*1 | Front door outside handle assembly (electrical key antenna) [for Driver Side] |
| Overhead + Passenger Side*2 | Front door outside handle assembly (electrical key antenna) [for Front Passenger Side] |
| Overhead + Front Room*3 | Indoor electrical key oscillator (front floor) |
| Overhead + Rear Room*4 | No. 2 indoor electrical key oscillator (rear floor) |
| Overhead + Luggage*5 | Electrical key antenna (outside luggage) |
| Luggage + Luggage (inside)*6 | No. 3 indoor electrical key oscillator (inside luggage) |
| Immobiliser Amp*7 | Amplifier (engine switch) |
Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.
![]() |
*1: Front door outside handle assembly (driver side electrical key antenna)
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.7 m (2.30 ft.) |
![]() |
*3: Indoor electrical key oscillator (front floor)
| *a | Inspection Point |
![]() |
*4: No. 2 indoor electrical key oscillator (inside luggage)
| *a | Inspection Point |
![]() |
*5: Electrical key antenna (outside luggage)
| *a | Approximately 0.7 m (2.30 ft.) |
![]() |
*6: No. 3 indoor electrical key oscillator (inside luggage)
| *a | Inspection Point |
![]() |
*7: Amplifier (engine switch)
| *A | w/o Panic Switch |
| *B | w/ Panic Switch |