Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
  1. Engage the 11 clamps.



    B314836E01
  1. Check that the matchmark of the fuel lid lock control cable sub-assembly is aligned with the center of the clamp.
    Text in Illustration 
    *a
    Matchmark



    B310925E01
  1. Install the fuel lid lock control cable sub-assembly as indicated by the arrows in the order shown in the illustration.



2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
  1. Connect the fuel lid lock control cable sub-assembly.

  1. Install the 2 nuts and fuel lid lock open lever sub-assembly.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Return the floor mat.



3. INSTALL HANDLE COVER
  1. Install the handle cover with the screw.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



4. INSTALL NO. 2 PACKAGE TRAY TRIM SPACER
  1. Install the No. 2 package tray trim spacer.

  1. Install the 3 clips.



5. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
  1. Engage the 8 clips install the quarter trim panel assembly LH.

  1. Install the clip.



6. INSTALL LUGGAGE COMPARTMENT TRIM COVER RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH (w/ Side Marker Light)
  1. Connect the connector.

  1. Install the luggage compartment inner trim cover LH with the 5 clips.



8. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH (w/o Side Marker Light)
  1. Install the luggage compartment inner trim cover LH with the 5 clips.



9. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH
  1. Install the 5 clips and the luggage compartment inner trim cover RH.



10. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 claws to install the rear floor finish plate.

  1. Install the 3 clips.



11. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


12. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH
  1. Engage the hook and install the separate type rear seat cushion assembly LH.

  1. Install the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



13. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL FRONT SEAT ASSEMBLY
(Click here)


15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B315249E01
  1. Align the alignment mark on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark

    NOTICE:
    After installation, check that the corners fit correctly.



16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 6 claws install the front door scuff plate LH.



18. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.