Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System) > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B167608E18

  1. Disconnect the D54 transponder key amplifier connector.

  2. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D54-7 (AGND) - Body ground
    -
    GR - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the D54 transponder key amplifier connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D54-1 (VC5) - D54-7 (AGND)
    Input
    R - GR
    Transponder key amplifier power supply
    Ignition switch ON
    4.5 to 5.5 V
    D54-4 (CODE) - D54-7 (AGND)
    Output
    LG - GR
    Demodulated signal of key code data
    Key inserted in ignition key cylinder
    Pulse generation
    D54-5 (TXCT) - D54-7 (AGND)
    Output
    W-G - GR
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311498E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  2. Disconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-1 (BECU) - Body ground
    Input
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-8 (IG) - Body ground
    Input
    None - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    Input
    None - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    MB-11 (GND) - Body ground
    -
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-32 (BMPX) - Body ground
    Input
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    D5-22 (KSW) - Body ground
    Input
    BR - Body ground
    Unlock warning switch input
    No key in ignition key cylinder (off)
    Below 1 V
    Key inserted ignition key cylinder (on)
    11 to 14 V
    D6-1 (GND) - Body ground
    -
    B - Body ground
    Ground
    Always
    Below 1 Ω
    A73-4 (GND) - Body ground
    -
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω

  4. Reconnect the D5, D6 and A73 main body ECU (network gateway ECU) connectors.

  5. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.

  6. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A73-5 (CODE) - Body ground
    Input
    LG - Body ground
    Demodulated signal of key code data
    Key inserted in ignition key cylinder
    Pulse generation
    A73-9 (IMO) - Body ground
    Input / output
    Y - Body ground
    EFI communication
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation
    A73-8 (VC5) - Body ground
    Output
    R - Body ground
    Transponder key amplifier power supply
    Ignition switch ON
    4.5 to 5.5 V
    A73-15 (TXCT) - Body ground
    Input
    W - Body ground
    Key code output signal
    Key inserted in ignition key cylinder
    Pulse generation
    A73-16 (AGND) - Body ground
    -
    GR - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    A73-17 (UART) - Body ground*
    Input / output
    SB - Body ground
    Transponder key ECU communication
    Key inserted in ignition key cylinder
    Pulse generation

    1. *: w/ Transponder Key ECU Assembly


CHECK TRANSPONDER KEY ECU ASSEMBLY

B315520E01

  1. Disconnect the A64 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A64-1 (+B) - Body ground
    Input
    L-R - Body ground
    Battery power supply
    Always
    11 to 14 V
    A64-5 (GND) - Body ground
    -
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the A64 transponder key ECU assembly connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A64-3 (UART) - A64-5 (GND)
    Input/Output
    SB - B-Y
    Main body ECU communication
    Key inserted in ignition key cylinder
    Pulse generation


CHECK ECM

A281924E01

  1. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A33-1 (+B2) - A36-4 (E01)
    Input
    V - B-L
    Battery power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A33-2 (BATT) - A36-4 (E01)
    Input
    W - B-L
    Battery power supply
    Always
    11 to 14 V
    A34-6 (+B) - A36-4 (E01)
    Input
    V - B-L
    Battery power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A35-25 (IMO) - A36-4 (E01)
    Input/Output
    Y - B-L
    Main body ECU communication
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation
    A36-4 (E01) - Body ground
    -
    B-L - Body ground
    Ground
    Always
    Below 1 Ω