Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR

COMPRESSOR > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL LEVEL


  1. for HFC-134a (R134a):



      E248883
    1. When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

      Standard:
      Drain oil from the new compressor assembly, and then add new oil so that the amount of oil in the new compressor assembly is the same as that in the compressor assembly to be replaced.

      HINT:
      The drain bolt and washer can be reused.

      NOTICE:
      1. When checking the compressor oil level, observe the precautions on the cooler removal/installation.
      2. If a new compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be excessive. This prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.
      3. If the volume of oil remaining in the removed compressor is too small, check for oil leaks.
      4. Be sure to use ND-OIL 8 or equivalent for compressor oil.



  1. for HFO-1234yf (R1234yf):



      E248883
    1. When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

      Standard:
      Drain oil from the new compressor assembly, and then add new oil so that the amount of oil in the new compressor assembly is the same as that in the compressor assembly to be replaced.

      HINT:
      The drain bolt and washer can be reused.

      NOTICE:
      1. When checking the compressor oil level, observe the precautions on the cooler removal/installation.
      2. If a new compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be excessive. This prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.
      3. If the volume of oil remaining in the removed compressor is too small, check for oil leaks.
      4. Be sure to use ND-OIL 12 or equivalent for compressor oil.



2. INSTALL COMPRESSOR WITH MAGNET CLUTCH


    E250732E01
  1. Install the compressor with magnet clutch with the 3 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.



3. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor with magnet clutch.

    Compressor oil:
    for HFC-134a (R134a):
    ND-OIL 8 or equivalent
    for HFO-1234yf (R1234yf):
    ND-OIL 12 or equivalent

  1. Install the O-ring onto the No. 1 cooler refrigerant discharge hose.

  1. Install the No. 1 cooler refrigerant discharge hose onto the compressor with magnet clutch with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



4. CONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor with magnet clutch.

    Compressor oil:
    for HFC-134a (R134a):
    ND-OIL 8 or equivalent
    for HFO-1234yf (R1234yf):
    ND-OIL 12 or equivalent

  1. Install the O-ring onto the suction hose sub-assembly.

  1. Install the suction hose sub-assembly onto the compressor with magnet clutch with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. INSTALL FAN AND GENERATOR V BELT


A276034E01
  1. Set the fan and generator V belt onto every part.
    Text in Illustration 
    *1
    Idler
    *2
    Generator
    *3
    Tensioner
    *4
    Water Pump
    *5
    Crankshaft
    *6
    A/C Compressor (w/ Air Conditioning System)
    Idler Pulley Bracket (w/o Air Conditioning System)

  1. While turning the belt tensioner clockwise, remove the 3 mm (0.118 in.) hexagon wrench.

    NOTICE:
    Make sure that the fan and generator V belt is properly installed to each pulley.

  1. Check that the fan and generator V belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the fan and generator V belt have not slipped out of the grooves on the bottom of the pulley.



6. INSTALL BELT GENERATOR COVER
  1. Install the belt generator cover with the 2 blots.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

  1. Engage the 2 wire harness clamps and install the wire harness to the belt generator cover.



7. INSTALL GENERATOR COVER
  1. Install the generator cover with the 2 blots.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }



8. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner cap with air cleaner hose with the 3 blots.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the air cleaner cap with air cleaner hose with the 2 hose clamps.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Connect the No. 2 ventilation hose.

  1. Connect the mass air flow meter connector.

  1. Engage the wire harness clamp and install the wire harness to the air cleaner cap.



9. CHARGE WITH REFRIGERANT
  1. for HFC-134a (R134a):

  1. for HFO-1234yf (R1234yf):



10. WARM UP ENGINE
  1. for HFC-134a (R134a):

  1. for HFO-1234yf (R1234yf):



11. INSPECT FOR REFRIGERANT LEAK
  1. for HFC-134a (R134a):

  1. for HFO-1234yf (R1234yf):