Home › Steering › STEERING COLUMN › STEERING WHEEL

STEERING WHEEL > REMOVAL

for Preparation Click here


NOTICE:
  1. Do not replace the spiral cable with the battery connected and the ignition switch ON.
  2. Do not rotate the spiral cable without the steering wheel with the battery connected and the ignition switch ON.
  3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



4. REMOVE HORN BUTTON ASSEMBLY

CAUTION:
When storing the horn button assembly, keep the airbag deployment side facing upward.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B457841E01
  1. Using a screwdriver wrapped with protective tape, remove the No. 1 and No. 2 lower steering wheel covers.
    Text in Illustration 
    *1
    Protective Tape



    B311351E01
  1. Using a screwdriver, push in the 3 torsion springs to disengage the 3 pins.
    Text in Illustration 
    *1
    Torsion Spring

    NOTICE:
    Do not drop the horn button assembly.

  1. Pull out the horn button assembly from the steering wheel assembly and support the horn button assembly with one hand.

    NOTICE:
    When removing the horn button assembly, do not pull the airbag wire harness.



  1. for Dual Airbag System



      B311944E01
    1. Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.
      Text in Illustration 
      *1
      Protective Tape
      *2
      Airbag Connector
      *3
      Horn Connector
      *4
      Airbag Connector Lock

    2. Disconnect the 2 airbag connectors to remove the horn button assembly.

      NOTICE:
      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    3. Disconnect the horn connector from the horn button assembly.



  1. for Single Airbag System



      B311352E01
    1. Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.
      Text in Illustration 
      *1
      Protective Tape
      *2
      Airbag Connector
      *3
      Horn Connector
      *4
      Airbag Connector Lock

    2. Disconnect the airbag connector to remove the horn button assembly.

      NOTICE:
      When disconnecting airbag connector, take care not to damage the airbag wire harness.

    3. Disconnect the horn connector from the horn button assembly.



5. REMOVE STEERING WHEEL ASSEMBLY


    C364398E01
  1. Remove the steering wheel assembly set nut.
    Text in Illustration 
    *1
    Matchmark

  1. Put matchmarks on the steering wheel assembly and steering column assembly.

  1. Disconnect the connectors from the spiral cable sub-assembly and steering wheel assembly.



    C260490E01
  1. Using SST, remove the steering wheel assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



6. REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (for Automatic Transmission)


    C261035
  1. Detach the clamp.



    C261036
  1. Remove the 4 screws and remove the shift paddle switch (transmission shift switch assembly).



7. REMOVE CRUISE CONTROL MAIN SWITCH ASSEMBLY (w/ Cruise Control System)


    E357512
  1. Disengage the clamp and disconnect the cruise control main switch wire connector.

  1. Remove the 2 screws and cruise control main switch assembly.



8. REMOVE STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)
  1. Disconnect the steering pad switch connector from the spiral cable sub-assembly.



    E356499
  1. Remove the 2 guides.



    E356500
  1. Remove the 2 screws.

  1. Disengage the 4 claws to remove the steering pad switch assembly.



9. REMOVE STEERING SHAKE DAMPER


    C364399
  1. Remove the 2 screws and steering shake damper from steering wheel assembly.



10. REMOVE LOWER STEERING WHEEL BOSS COVER


    C364400
  1. Disengage the 4 claws and remove the lower steering wheel boss cover from steering wheel assembly.



11. REMOVE NO. 1 STEERING WHEEL ORNAMENT (w/o Steering Pad Switch)


    E357513
  1. Remove the 2 screws.

  1. Disengage the 4 claws to remove the No. 1 steering wheel ornament.