Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The following procedure is for the LH side.



1. CLEAN QUARTER WINDOW ASSEMBLY


    BO04421
  1. Clean the outer edges of the quarter window assembly with a non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Be careful not to damage the glass or clips.



2. INSTALL QUARTER WINDOW ASSEMBLY LH
  1. Using a brush or a sponge, apply primer (3M N-200) to the quarter window glass adhesive dam attachment surface of the quarter window assembly LH.



  1. Install the new quarter window glass adhesive dam, applying double-sided tape all the way around the glass except where the dam is installed, as shown in the illustration.


    B309204E01


    Standard Dimension:

    Area
    Dimension
    a
    13.0 mm (0.5118 in.)
    b
    72.5 mm (2.8543 in.)
    c
    13.0 mm (0.5118 in.)
    d
    62.3 mm (2.4528 in.)
    e
    23.4 mm (0.9213 in.)
    f
    123.8 mm (4.874 in.)


    Text in Illustration 
    *1
    Quarter Window Glass Adhesive Dam
    -
    -

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



    B295410E01
  1. Using a brush, coat the installation surface on the vehicle body with Primer (Sunstar #435-40).
    Text in Illustration 
    *a
    NG
    *b
    OK
    V100145
    Primer (Sunstar #435-40)
    V100155
    Adhesive

    NOTICE:
    1. Do not coat the adhesive with Primer (Sunstar #435-40).
    2. Do not apply too much primer.
    3. Allow the primer to dry for 3 minutes or more.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Using a brush or a sponge, coat the application area of adhesive with Primer (3M N-200).


    B309205E01


    Standard Dimension:

    Item
    Dimension
    a
    8.0 mm (0.315 in.)
    b
    22.3 mm (0.878 in.)
    c
    10.1 mm (0.398 in.)
    d
    13.9 mm (0.547 in.)


    Text in Illustration 
    V100155
    Primer (3M N-200)
    -
    -

    NOTICE:
    1. Do not apply too much primer.
    2. Allow the primer to dry for 3 minutes or more.

    HINT:
    If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



  1. Apply adhesive to the quarter window assembly LH.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E03
    1. Cut off the tip of the cartridge nozzle, as shown in the illustration.

      Standard Dimension:
      Item
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

    2. Load the sealer gun with cartridge.



    3. Apply adhesive to the quarter window assembly LH, as shown in the illustration.


      B309206E01


      Standard Dimension:

      Item
      Dimension
      a
      8.0 mm (0.315 in.)
      b
      12.0 mm (0.4724 in.)
      c
      5.6 mm (0.2205 in.)
      d
      26.3 mm (1.0354 in.)
      e
      50.0 mm (1.9685 in.)


      Text in Illustration 
      V100155
      Adhesive
      -
      -

      HINT:
      Apply adhesive onto the ceramic notches.



  1. Install the quarter window assembly LH to the vehicle body (When reusing the quarter window assembly LH).

    1. Install the butyl tape (If the clips are broken).



    2. B309199E01
    3. Position the quarter window assembly LH so that the matchmarks are aligned, and press it in gently along the rim.
      Text in Illustration 
      *1
      Matchmark

    4. Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.

  1. Install the quarter window assembly LH (When using a new quarter window assembly LH).

    1. Engage the 3 clips to install the quarter window assembly LH.

      NOTICE:
      Allow the primer to dry for 3 minutes or more.

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.

  1. Hold the quarter window assembly LH in place securely with protective tape or equivalent until the adhesive hardens.

    NOTICE:
    1. Check that the clips are attached to the body correctly.
    2. Check the clearance between the body and the glass.

  1. Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.



    BO03986E16
  1. Using a scraper, remove any excess or protruding adhesive.

    HINT:
    Apply adhesive onto the glass rim.

  1. Hold the quarter window assembly LH using protective tape until the applied adhesive becomes hard.



3. INSPECT WATER LEAK
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



4. INSTALL CENTER PILLAR GARNISH LH
  1. Engage the 2 guides and clip.

  1. Install the center pillar garnish LH with the 2 bolts and clip.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



5. INSTALL REAR QUARTER TRIM FRONT GARNISH LH
  1. Engage the claw and clip.

  1. Install the rear quarter trim front garnish LH with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



6. INSTALL REAR WINDOW SIDE GARNISH LH
  1. Engage the guide and 2 clips.

  1. Install the rear window side garnish LH with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



7. INSTALL QUARTER TRIM LID SUB-ASSEMBLY LH
  1. Install the 2 lid cover clips from the quarter trim lid sub-assembly LH.

    NOTICE:
    If there is any damage, be sure to replace the lid cover clip with a new one.



    B321466E01
  1. Engage the 2 guides and 6 claws and install the quarter trim lid sub-assembly LH.
    Text in Illustration 
    *1
    Lid Cover Clip



8. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
  1. Engage the 8 clips install the quarter trim panel assembly LH.

  1. Install the clip.



9. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
  1. Fold down the rear seatback assembly.

  1. Engage the 2 clips install the luggage compartment inner trim cover LH.



10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B315249E01
  1. Align the alignment mark on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark

    NOTICE:
    After installation, check that the corners fit correctly.



11. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 6 claws install the front door scuff plate LH.



12. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH



13. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH
  1. Engage the hook and install the separate type rear seat cushion assembly LH.

  1. Install the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }