Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
  1. The the quarter window glass assembly can be reused. When installing the window, if any of the clips on the quarter window glass are broken, butyl tape can be used to support the glass until the applied adhesive hardens.
  2. When using butyl tape to temporarily secure the window, make sure that the butyl tape is not applied exactly at the original clip location. If the butyl tape is applied exactly at the clip location, it will cause the window to protrude
  3. Use the same procedure for both the RH and LH sides.
  4. The following procedure is for the LH side.



1. REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH


    B299993
  1. Remove the bolt.

  1. Disengage the hook and remove the separate type rear seat cushion assembly LH.



2. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY



3. REMOVE FRONT DOOR SCUFF PLATE LH


    B315201
  1. Disengage the 6 claws and remove the front door scuff plate LH.



4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the luggage compartment trim cover LH.



5. REMOVE NO. 2 FRONT DOOR WEATHERSTRIP LH


    B330655
  1. Disengage the 4 clips and remove the No. 2 front door weatherstrip LH.



6. REMOVE ROOF DRIP SIDE FINISH MOULDING LH


    B330656
  1. Remove the 7 screws and the roof drip side finish moulding LH.

    CAUTION:
    Wear protective gloves. Sharp areas on the parts may injure your hands.



7. DISCONNECT LUGGAGE COMPARTMENT INNER TRIM COVER LH


    B321716
  1. Fold down the bench type rear seatback assembly.

  1. Disengage the 2 clips and disconnect the luggage compartment inner trim cover LH.



8. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH


    B315207
  1. Pull up the rear seatback assembly.

  1. Remove the clip.

  1. Disengage the 8 clips and remove the luggage compartment trim cover LH.



9. REMOVE QUARTER TRIM LID SUB-ASSEMBLY LH


    B315208
  1. Along the arrow in the illustration, disengage the 6 claws.



    B315209
  1. Disengage the 2 clips and 2 guides.

    HINT:
    Make the quarter trim lid sub-assembly LH hang down from the lid cover clip.



    B316678E01
  1. Push the lid cover clip knobs in the direction of the arrow to remove the 2 lid cover clips along with the quarter trim lid sub-assembly LH.
    Text in Illustration 
    *1
    Lid Cover Clip

  1. Remove the 2 lid cover clips from the lid cover LH.

    NOTICE:
    If there is any damage, be sure to replace the lid cover clip with a new one.



10. REMOVE REAR WINDOW SIDE GARNISH LH


    B315213
  1. Remove the bolt.

  1. Disengage the 2 clips and guide remove the rear window side garnish LH.



11. REMOVE REAR QUARTER TRIM FRONT GARNISH LH


    B315215
  1. Remove the 2 bolts.

  1. Disengage the clip and claw remove the rear quarter trim front garnish LH.



12. REMOVE CENTER PILLAR GARNISH LH


    B317118
  1. Remove the 2 bolts and clip.

  1. Disengage the clips and 2 guides to remove the center pillar garnish LH.



13. REMOVE QUARTER WINDOW ASSEMBLY LH


    B309198E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape



  1. When reusing the quarter window assembly LH.



      B309199E01
    1. Place matchmarks on the quarter window assembly LH and vehicle body on the locations indicated in the illustration.
      Text in Illustration 
      *1
      Matchmark



    B309201E01
  1. Pass a piano wire between the vehicle body and quarter window assembly LH from the interior, as shown in the illustration.
    Text in Illustration 
    *1
    Piano Wire

    HINT:
    Ensure not to interfere with the clips when passing the piano wire.

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    NOTICE:
    When separating the quarter window assembly LH from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

  1. Cut off the adhesive by pulling the piano wire around the quarter window assembly LH.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



    B309202
  1. Disengage the 3 clips.

  1. Using suction cups, remove the quarter window assembly LH.

    NOTICE:
    Be careful not to drop the quarter window assemblyLH.



14. REMOVE QUARTER WINDOW GLASS ADHESIVE DAM


    B309203E01
  1. When reusing the quarter window assembly LH.

    1. Using a scraper, remove the quarter window glass adhesive dam.
      Text in Illustration 
      *1
      Quarter Window Glass Adhesive Dam

      NOTICE:
      1. Be careful not to damage the quarter window assembly LH.
      2. Be sure to replace the quarter window glass adhesive dam with a new one.



15. CLEAN VEHICLE BODY


  1. Clean and shape the contact surface of the vehicle body.



    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.



      B309172E01


      Text in Illustration 
      *1
      Body
      -
      -
      V100145
      Adhesive
      -
      -

      Standard Dimension:

      Area
      Dimension
      a
      2.0 mm (0.0787 in.)

    2. Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.