Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > DISASSEMBLY

for Preparation Click here



1. REMOVE HOOD TO FRONT END PANEL SEAL


    B322369
  1. Remove the 13 clips and hood to front end panel seal from the front bumper upper retainer.



2. REMOVE NO. 2 FRONT BUMPER SIDE SUPPORT LH


    B312510
  1. Remove the screw.



    B312511
  1. Disengage the 2 claws and remove the No. 2 front bumper side support LH.



3. REMOVE NO. 2 FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE FRONT BUMPER REINFORCEMENT PLATE LH


    B312512
  1. Remove the 2 clips and the front bumper reinforcement plate LH.



5. REMOVE FRONT BUMPER REINFORCEMENT PLATE RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE FRONT LOWER BUMPER COVER


    B312513
  1. Remove the 3 bolts.

  1. Remove the 4 clips and the front lower bumper cover.



7. REMOVE FRONT BUMPER STAY BRACKET


    B312514
  1. Remove the 3 bolts and the front bumper stay bracket.



8. REMOVE FRONT BUMPER ENERGY ABSORBER


    B312515
  1. Remove the front bumper energy absorber.



9. REMOVE RADIATOR COVER PLATE


    B312516
  1. Remove the 6 clips and the radiator cover plate.



10. REMOVE HIGH PITCHED HORN ASSEMBLY (except China)


    B312523
  1. Disconnect the connector.

  1. Remove the bolt, and the high pitched horn assembly with horn bracket sub-assembly.



11. REMOVE LOW PITCHED HORN ASSEMBLY (for China)


    B312523
  1. Disconnect the connector.

  1. Remove the bolt, and the low pitched horn assembly with horn bracket sub-assembly.



12. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B312517
  1. Remove the 8 bolts and the front bumper reinforcement sub-assembly.



13. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    B314947E01
  1. Apply protective tape to the front bumper cover in the area around the radiator grille emblem.
    Text in Illustration 
    *1
    Wooden Block
    *2
    Piano Wire
    *3
    Protective Tape
    *4
    Location Pin

  1. Using an infrared light, heat the front bumper cover and the radiator grille emblem.

    Heating Temperature:
    Item
    Temperature
    Front Bumper Cover
    40 to 60°C (104 to 140°F)
    Radiator Grille Emblem
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself with the hot front bumper cover and radiator grille emblem or with the infrared light.

    NOTICE:
    Do not heat the front bumper cover and radiator grille emblem excessively.

  1. Insert piano wire between the front bumper cover and radiator grille emblem.

    HINT:
    Be careful of the location pin positions.

  1. Tie objects that can serve as handles (for example, wooden blocks) to the piano wire ends.

  1. Pull the piano wire and scrape off the double-sided tape that holds the radiator grille emblem to the front bumper cover.

    NOTICE:
    Be careful not to damage the front bumper cover.

  1. Remove the 2 push nuts and the radiator grille emblem.



14. REMOVE NO. 1 LOWER RADIATOR GRILLE


    B312519
  1. Disengage the 20 claws and remove the No. 1 lower radiator grille.



15. REMOVE FRONT BUMPER HOLE COVER LH


    B312518
  1. Remove the 3 screws and the front bumper hole cover LH.



16. REMOVE FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure as for the LH side.



17. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    B312209
  1. Disconnect the connector.

  1. Remove the 2 screws.



    B312210
  1. Disengage the 2 guides and remove the fog light assembly.



18. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



19. REMOVE FOG LIGHT COVER LH


    B312522
  1. Disengage the 10 claws and remove the fog light cover LH.



20. REMOVE FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



21. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY LH


    E249682
  1. Remove the 2 nuts.

  1. Disconnect the connector.



    E249683
  1. Disengage the 2 claws to remove the front turn signal light assembly.



22. REMOVE FRONT TURN SIGNAL LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.


23. REMOVE FRONT BUMPER HOLE COVER


    B312520
  1. Disengage the 4 claws and remove the front bumper hole cover.



24. REMOVE FRONT SPOILER COVER (for Sport Package)


    B312943
  1. Remove the 3 clips.

  1. Peel off the double-sided tape.
    Text in Illustration 
    V100144
    Double-sided Tape



    B312945
  1. Disengage the 8 claws and remove the front spoiler cover.



25. REMOVE FRONT SPOILER COVER LH (for Sport Package)


    B312944
  1. Remove the clip.

  1. Peel off the double-sided tape.
    Text in Illustration 
    V100144
    Double-sided Tape



    B312946
  1. Disengage the claw and remove the front spoiler cover LH.



26. REMOVE FRONT SPOILER COVER RH (for Sport Package)

HINT:
Use the same procedure as for the LH side.



27. REMOVE FRONT SPOILER RETAINER LH (for Sport Package)


    B312983
  1. Remove the 2 screws.



    B322392E01
  1. Put matchmarks on the front bumper cover as shown in the illustration before remove the rear spoiler retainer LH.
    Text in Illustration 
    *a
    Matchmark



    B312984
  1. Slide the rear spoiler retainer LH as shown in the illustration and remove it.



28. REMOVE FRONT SPOILER RETAINER RH (for Sport Package)

HINT:
Use the same procedure as for the LH side.