Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SPOILER RETAINER LH (for Sport Package)


    B312995
  1. Slide the front spoiler retainer LH as shown in the illustration to install it.

    HINT:
    B322388E01
    Align the front spoiler retainer LH in the position shown in the installation.

    Text in Illustration 
    *1
    Front Spoiler Retainer LH
    *a
    Edge of the Front Bumper Cover
    *b
    Matchmark



    B312983
  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



2. INSTALL FRONT SPOILER RETAINER RH (for Sport Package)

HINT:
Use the same procedure as for the LH side.



3. INSTALL FRONT SPOILER COVER LH (for Sport Package)
  1. Clean the front bumper cover surface.

    1. Using a heat light, heat the front bumper cover surface.

    2. Remove the double-sided tape from the front bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install the front spoiler cover LH.

    1. Apply primer to the front spoiler cover LH attachment surface of the front bumper cover.

    2. Using a heat light, heat the front bumper cover and the front spoiler cover LH.

    3. Remove the peeling paper from the front spoiler cover LH.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    4. B312946
    5. Engage the claw and install the front spoiler cover LH.



    6. B312944
    7. Apply thorough pressure to the sections with double-sided tape.
      Text in Illustration 
      V100144
      Double-sided Tape

    8. Install the clip.



4. INSTALL FRONT SPOILER COVER RH (for Sport Package)

HINT:
Use the same procedure as for the LH side.



5. INSTALL FRONT SPOILER COVER (for Sport Package)
  1. Clean the front bumper cover surface.

    1. Using a heat light, heat the front bumper cover surface.

    2. Remove the double-sided tape from the front bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Install the front spoiler cover.

    1. Apply primer to the front spoiler cover attachment surface of the front bumper cover.

    2. Using a heat light, heat the front bumper cover and the front spoiler cover.

    3. Remove the peeling paper from the front spoiler cover.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    4. B312945
    5. Engage the 8 claws and install the front spoiler cover.



    6. B312943
    7. Apply thorough pressure to the sections with double-sided tape.
      Text in Illustration 
      V100144
      Double-sided Tape

    8. Install the 3 clips.



6. INSTALL FRONT BUMPER HOLE COVER


    B312520
  1. Engage the 4 claws to install the front bumper hole cover.



7. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH
  1. Engage the 2 claws to install the front turn signal light assembly.

  1. Install the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



8. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL FOG LIGHT COVER LH


    B312522
  1. Engage the 10 claws to install the fog light cover LH.



10. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    B312213
  1. Engage the 2 guides to install the fog light assembly.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Connect the connector.



12. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



13. INSTALL FRONT BUMPER HOLE COVER LH


    B312518
  1. Install the front bumper hole cover LH with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



14. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure as for the LH side.



15. INSTALL NO. 1 LOWER RADIATOR GRILLE


    B312519
  1. Engage the 20 claws to install the No. 1 lower radiator grille.



16. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.

      Heating Temperature:
      Item
      Temperature
      Front Bumper Cover
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself with the hot front bumper cover or with the infrared light.

      NOTICE:
      Do not heat the front bumper cover excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the front bumper cover while it is hot from the infrared light.

      NOTICE:
      Installing the radiator grille emblem while any double-sided tape remains on the front bumper cover may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Using an infrared light, heat the radiator grille emblem installation surface of the front bumper cover and new radiator grille emblem.

    Heating Temperature:
    Item
    Temperature
    Front Bumper Cover
    40 to 60°C (104 to 140°F)
    Radiator Grille Emblem
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself withthe hot front bumper cover and radiator grille emblem or with the infrared light.

    NOTICE:
    Do not heat the front bumper cover and radiator grille emblem excessively.



    B313061E01
  1. Insert the 2 pins into the front bumper cover and install a new radiator grille emblem with the new 2 push nuts.
    Text in Illustration 
    *1
    Location Pin



17. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B312517
  1. Install the front bumper reinforcement sub-assembly with the 8 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



18. INSTALL LOW PITCHED HORN ASSEMBLY (for China)
  1. Install the bolt and low pitched horn assembly with horn bracket sub-assembly.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector.



19. INSTALL HIGH PITCHED HORN ASSEMBLY (except China)
  1. Install the bolt and high pitched horn assembly with horn bracket sub-assembly.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector.



20. INSTALL RADIATOR COVER PLATE


    B312516
  1. Install the radiator cover plate with the 6 clips.



21. INSTALL FRONT BUMPER ENERGY ABSORBER


    B312515
  1. Install the front bumper energy absorber.



22. INSTALL FRONT BUMPER STAY BRACKET


    B312514
  1. Install the front bumper stay bracket with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



23. INSTALL FRONT LOWER BUMPER COVER


    B312513
  1. Install the front lower bumper cover with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the 4 clips.



24. INSTALL FRONT BUMPER REINFORCEMENT PLATE LH


    B312512
  1. Install the front bumper reinforcement plate LH with the 2 clips.



25. INSTALL FRONT BUMPER REINFORCEMENT PLATE RH

HINT:
Use the same procedure as for the LH side.



26. INSTALL NO. 2 FRONT BUMPER SIDE SUPPORT LH


    B312511
  1. Engage the 2 claws.



    B312510
  1. Install the No. 2 front bumper side support LH with the screw.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



27. INSTALL NO. 2 FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure as for the LH side.



28. INSTALL HOOD TO FRONT END PANEL SEAL


    B322369
  1. Install the hood to front end panel seal to the front bumper upper retainer with the 13 clips.