FRONT BUMPER > REASSEMBLY |
| 1. INSTALL FRONT SPOILER RETAINER LH (for Sport Package) |
![]() |
Slide the front spoiler retainer LH as shown in the illustration to install it.
![]() |
| *1 | Front Spoiler Retainer LH |
| *a | Edge of the Front Bumper Cover |
| *b | Matchmark |
![]() |
Install the 2 screws.
| 2. INSTALL FRONT SPOILER RETAINER RH (for Sport Package) |
| 3. INSTALL FRONT SPOILER COVER LH (for Sport Package) |
Clean the front bumper cover surface.
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install the front spoiler cover LH.
Apply primer to the front spoiler cover LH attachment surface of the front bumper cover.
Using a heat light, heat the front bumper cover and the front spoiler cover LH.
Remove the peeling paper from the front spoiler cover LH.
![]() |
Engage the claw and install the front spoiler cover LH.
![]() |
Apply thorough pressure to the sections with double-sided tape.
![]() | Double-sided Tape |
Install the clip.
| 4. INSTALL FRONT SPOILER COVER RH (for Sport Package) |
| 5. INSTALL FRONT SPOILER COVER (for Sport Package) |
Clean the front bumper cover surface.
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install the front spoiler cover.
Apply primer to the front spoiler cover attachment surface of the front bumper cover.
Using a heat light, heat the front bumper cover and the front spoiler cover.
Remove the peeling paper from the front spoiler cover.
![]() |
Engage the 8 claws and install the front spoiler cover.
![]() |
Apply thorough pressure to the sections with double-sided tape.
![]() | Double-sided Tape |
Install the 3 clips.
| 6. INSTALL FRONT BUMPER HOLE COVER |
![]() |
Engage the 4 claws to install the front bumper hole cover.
| 7. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH |
Engage the 2 claws to install the front turn signal light assembly.
Install the 2 nuts.
| 8. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH |
| 9. INSTALL FOG LIGHT COVER LH |
![]() |
Engage the 10 claws to install the fog light cover LH.
| 10. INSTALL FOG LIGHT COVER RH |
| 11. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) |
![]() |
Engage the 2 guides to install the fog light assembly.
Install the 2 screws.
Connect the connector.
| 12. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light) |
| 13. INSTALL FRONT BUMPER HOLE COVER LH |
![]() |
Install the front bumper hole cover LH with the 3 screws.
| 14. INSTALL FRONT BUMPER HOLE COVER RH |
| 15. INSTALL NO. 1 LOWER RADIATOR GRILLE |
![]() |
Engage the 20 claws to install the No. 1 lower radiator grille.
| 16. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.
| Item | Temperature |
| Front Bumper Cover | 40 to 60°C (104 to 140°F) |
Using a piece of cloth, rub the remaining double-sided tape off the front bumper cover while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Using an infrared light, heat the radiator grille emblem installation surface of the front bumper cover and new radiator grille emblem.
| Item | Temperature |
| Front Bumper Cover | 40 to 60°C (104 to 140°F) |
| Radiator Grille Emblem | 20 to 30°C (68 to 86°F) |
![]() |
Insert the 2 pins into the front bumper cover and install a new radiator grille emblem with the new 2 push nuts.
| *1 | Location Pin |
| 17. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
![]() |
Install the front bumper reinforcement sub-assembly with the 8 bolts.
| 18. INSTALL LOW PITCHED HORN ASSEMBLY (for China) |
Install the bolt and low pitched horn assembly with horn bracket sub-assembly.
Connect the connector.
| 19. INSTALL HIGH PITCHED HORN ASSEMBLY (except China) |
Install the bolt and high pitched horn assembly with horn bracket sub-assembly.
Connect the connector.
| 20. INSTALL RADIATOR COVER PLATE |
![]() |
Install the radiator cover plate with the 6 clips.
| 21. INSTALL FRONT BUMPER ENERGY ABSORBER |
![]() |
Install the front bumper energy absorber.
| 22. INSTALL FRONT BUMPER STAY BRACKET |
![]() |
Install the front bumper stay bracket with the 3 bolts.
| 23. INSTALL FRONT LOWER BUMPER COVER |
![]() |
Install the front lower bumper cover with the 3 bolts.
Install the 4 clips.
| 24. INSTALL FRONT BUMPER REINFORCEMENT PLATE LH |
![]() |
Install the front bumper reinforcement plate LH with the 2 clips.
| 25. INSTALL FRONT BUMPER REINFORCEMENT PLATE RH |
| 26. INSTALL NO. 2 FRONT BUMPER SIDE SUPPORT LH |
![]() |
Engage the 2 claws.
![]() |
Install the No. 2 front bumper side support LH with the screw.
| 27. INSTALL NO. 2 FRONT BUMPER SIDE SUPPORT RH |
| 28. INSTALL LICENSE PLATE BRACKET |
![]() |
Type A
Install the license plate bracket with the 2 bolts.
![]() |
Type B
Install the license plate bracket with the 2 bolts.
| 29. INSTALL HOOD TO FRONT END PANEL SEAL |
![]() |
Install the hood to front end panel seal to the front bumper upper retainer with the 13 clips.