Home › Vehicle Interior › INTERIOR PANELS / TRIM › FRONT CONSOLE BOX

FRONT CONSOLE BOX > INSTALLATION

for Preparation Click here



1. INSTALL CONSOLE BOX ASSEMBLY
  1. Connect the connector.

  1. Install the console box assembly with the 4 screws and 2 bolts.

    Torque:
    Bolt:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



2. INSTALL INSTRUMENT PANEL FINISH PANEL END LH
  1. Engage the 4 claws to install the instrument panel finish panel end LH.



3. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL PARKING BRAKE HOLE COVER
  1. Engage the 5 claws to install the parking brake hole cover.



5. INSTALL CUP HOLDER CUSHION
  1. Install the cup holder cushion.



6. INSTALL INSTRUMENT PANEL CUP HOLDER
  1. Install the instrument panel cup holder.



7. INSTALL NO. 1 ASH RECEPTACLE SUB-ASSEMBLY (w/ Ashtray)
  1. Install the No. 1 ash receptacle sub-assembly.



8. INSTALL PATTERN SELECT SWITCH ASSEMBLY (for Manual Transmission)
  1. Install the 2 screws and the pattern select switch assembly to the shifting hole cover sub-assembly.

  1. Connect the pattern select switch assembly connector clamp. (for Automatic Transmission)

  1. Connect the pattern select switch assembly connector.



9. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transmission)
  1. Install the shifting hole cover sub-assembly with the 4 screws.



10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transmission)
  1. Connect the connector.

  1. Engage the 2 clips and 4 claws to install the upper console panel sub-assembly.



11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)


    B317120E01
  1. Turn the knob clockwise to install the shift lever knob sub-assembly.
    Text in Illustration 
    *1
    Pull collar

    NOTICE:
    1. Tighten the shift lever knob until the tightening on the shift lever knob stiffens.
    2. Check that the transmission moves into reverse when the pull collar is pulled.



12. INSTALL PATTERN SELECT SWITCH ASSEMBLY (for Automatic Transmission)
  1. Install the pattern select switch assembly with the 2 screws.



13. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Automatic Transmission)
  1. Engage the claw.

  1. Install the shifting hole cover sub-assembly with the 2 screws.



14. INSTALL SHIFT POSITION INDICATOR (for Automatic Transmission)
  1. Engage the clamp.

  1. Install the shift position indicator with the 2 screws.



15. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transmission)
  1. Connect the connector.

  1. Engage the 2 clips and 4 claws to install the upper console panel sub-assembly.



16. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission)


    B315239
  1. Turn the knob clockwise to install the shift lever knob sub-assembly.

    NOTICE:
    1. Tighten the shift lever knob until the tightening on the shift lever knob stiffens.

    1. B321464E01
      Face the groove on the shift lever knob toward the rear of the vehicle.
      Text in Illustration 
      *1
      Groove



17. INSTALL NO. 1 STEREO JACK ADAPTER ASSEMBLY (w/ Stereo Jack Adapter)
  1. Engage the 2 claws to install the No. 1 stereo jack adapter assembly.



18. INSTALL FRONT CONSOLE BOX COVER (w/o Entry and Start System)
  1. Engage the 6 claws to install the front console box cover.



19. INSTALL INDOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)
  1. Engage the clamp to install the indoor electrical key oscillator.



20. INSTALL PUSH START SWITCH (w/ Entry and Start System)
  1. Connect the 2 claws, and install the engine switch.

  1. Connect the engine switch connector.



21. INSTALL FRONT CONSOLE BOX COVER (w/ Entry and Start System)
  1. Connect the connector.

  1. Engage the 6 claws to install the front console box cover.