Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here



1. INSTALL RADIATOR GRILLE EMBLEM (for Front Side)
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.

      Heating Temperature:
      Item
      Temperature
      Front Bumper Cover
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself with the hot front bumper cover or with the infrared light.

      NOTICE:
      Do not heat the front bumper cover excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the front bumper cover while it is hot from the infrared light.

      NOTICE:
      Installing the radiator grille emblem while any double-sided tape remains on the front bumper cover may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Using an infrared light, heat the radiator grille emblem installation surface of the front bumper cover and new radiator grille emblem.

    Heating Temperature:
    Item
    Temperature
    Front Bumper Cover
    40 to 60°C (104 to 140°F)
    Radiator Grille Emblem
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself withthe hot front bumper cover and radiator grille emblem or with the infrared light.

    NOTICE:
    Do not heat the front bumper cover and radiator grille emblem excessively.



    B313061E01
  1. Insert the 2 pins into the front bumper cover and install a new radiator grille emblem with the new 2 push nuts.
    Text in Illustration 
    *1
    Location Pin



2. INSTALL FRONT BUMPER COVER
(Click here)


3. INSTALL RADIATOR GRILLE EMBLEM (for Rear Side)
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      Heating Temperature:
      Item
      Temperature
      Luggage Compartment Door Panel
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself with the hot luggage compartment door panel or with the infrared light.

      NOTICE:
      Do not heat the luggage compartment door panel excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the radiator grille emblem while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Using an infrared light, heat the radiator grille emblem installation surface of the luggage compartment door panel and new radiator grille emblem.

    Heating Temperature:
    Item
    Temperature
    Luggage Compartment Door Panel
    40 to 60°C (104 to 140°F)
    Radiator Grille Emblem
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself with the hot luggage compartment door panel and radiator grille emblem or with the infrared light.

    NOTICE:
    Do not heat the luggage compartment door panel and radiator grille emblem excessively.



    B313063E01
  1. Insert the 2 pins into the luggage compartment door panel and install a new radiator grille emblem.
    Text in Illustration 
    *1
    Location Pin



4. INSTALL LUGGAGE COMPARTMENT DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      Heating Temperature:
      Item
      Temperature
      Luggage Compartment Door Panel
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself with the hot luggage compartment door panel or with the infrared light.

      NOTICE:
      Do not heat the luggage compartment door panel excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Using an infrared light, heat the back door name plate installation surface of the luggage compartment door panel and new luggage compartment door name plate.

    Heating Temperature:
    Item
    Temperature
    Luggage Compartment Door Panel
    40 to 60°C (104 to 140°F)
    Luggage Compartment Door Name Plate
    20 to 30°C (68 to 86°F)

    CAUTION:
    Do not burn yourself with the hot luggage compartment door panel and luggage compartment door name plate or with the infrared light.

    NOTICE:
    Do not heat the luggage compartment door panel and luggage compartment door name plate excessively.



    B314951E01
  1. Install a new luggage compartment door name plate as shown in the illustration.
    Text in Illustration 
    *1
    Luggage Compartment Door Name Plate
    *2
    Luggage Compartment Door Panel
    *3
    Bracket

    1. Install the enclosed bracket with luggage compartment door name plate, to the luggage compartment door panel.

    2. Remove the release paper from the luggage compartment door name plate.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Using the bracket, install the luggage compartment door name plate.

    4. Remove the bracket from luggage compartment door panel.