NAME PLATE > INSTALLATION |
| 1. INSTALL RADIATOR GRILLE EMBLEM (for Front Side) |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.
| Item | Temperature |
| Front Bumper Cover | 40 to 60°C (104 to 140°F) |
Using a piece of cloth, rub the remaining double-sided tape off the front bumper cover while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Using an infrared light, heat the radiator grille emblem installation surface of the front bumper cover and new radiator grille emblem.
| Item | Temperature |
| Front Bumper Cover | 40 to 60°C (104 to 140°F) |
| Radiator Grille Emblem | 20 to 30°C (68 to 86°F) |
![]() |
Insert the 2 pins into the front bumper cover and install a new radiator grille emblem with the new 2 push nuts.
| *1 | Location Pin |
| 2. INSTALL FRONT BUMPER COVER |
| 3. INSTALL LETTER MARK |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the front fender.
| Item | Temperature |
| Front Fender | 40 to 60°C (104 to 140°F) |
Using a piece of cloth, rub the remaining double-sided tape off the front fender while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Using an infrared light, heat the back door name plate installation surface of the front fender and new letter mark.
| Item | Temperature |
| Front Fender | 40 to 60°C (104 to 140°F) |
| Letter Mark | 20 to 30°C (68 to 86°F) |
![]() |
Install a new letter mark as shown in the illustration.
| *1 | Letter Mark |
| *2 | Bracket |
| *3 | Front Fender Edge |
| *4 | Bottom Line of Front Fender Recessed Area |
Align the enclosed bracket with letter mark with the front fender as shown in the illustration.
Remove the release paper from the letter mark.
Using the bracket, install the letter mark.
Remove the bracket from the front fender.
| 4. INSTALL RADIATOR GRILLE EMBLEM (for Rear Side) |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.
| Item | Temperature |
| Luggage Compartment Door Panel | 40 to 60°C (104 to 140°F) |
Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Using an infrared light, heat the radiator grille emblem installation surface of the luggage compartment door panel and new radiator grille emblem.
| Item | Temperature |
| Luggage Compartment Door Panel | 40 to 60°C (104 to 140°F) |
| Radiator Grille Emblem | 20 to 30°C (68 to 86°F) |
![]() |
Insert the 2 pins into the luggage compartment door panel and install a new radiator grille emblem.
| *1 | Location Pin |
| 5. INSTALL LUGGAGE COMPARTMENT DOOR NAME PLATE |
Clean the attachment surface.
Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.
| Item | Temperature |
| Luggage Compartment Door Panel | 40 to 60°C (104 to 140°F) |
Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.
Using a non-residue solvent, clean the attachment surface.
Using an infrared light, heat the back door name plate installation surface of the luggage compartment door panel and new luggage compartment door name plate.
| Item | Temperature |
| Luggage Compartment Door Panel | 40 to 60°C (104 to 140°F) |
| Luggage Compartment Door Name Plate | 20 to 30°C (68 to 86°F) |
![]() |
Install a new luggage compartment door name plate as shown in the illustration.
| *1 | Luggage Compartment Door Name Plate |
| *2 | Luggage Compartment Door Panel |
| *3 | Bracket |
Align the enclosed bracket with luggage compartment door name plate with the luggage compartment door panel.
Remove the release paper from the luggage compartment door name plate.
Using the bracket, install the luggage compartment door name plate.
Remove the bracket from the luggage compartment door panel.