Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E177570E14


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio receiver assembly and speakers.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D14-1 (FR+) - D39-4 (+)
    Always
    Below 1 Ω
    D14-5 (FR-) - D39-2 (-)
    Always
    Below 1 Ω
    D14-2 (FL+) - D66-4 (+)
    Always
    Below 1 Ω
    D14-6 (FL-) - D66-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D66-3 (+) - E6-1
    Always
    Below 1 Ω
    D66-1 (-) - E6-2
    Always
    Below 1 Ω
    D39-3 (+) - F9-1
    Always
    Below 1 Ω
    D39-1 (-) - F9-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D13-1 (RR+) - G15-1
    Always
    Below 1 Ω
    D13-3 (RR-) - G15-2
    Always
    Below 1 Ω
    D13-2 (RL+) - H24-1
    Always
    Below 1 Ω
    D13-6 (RL-) - H24-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D14-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    D14-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    D14-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    D14-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    D13-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    D13-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    D13-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    D13-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D66-3 (+) - Body ground
    Always
    10 kΩ or higher
    D66-1 (-) - Body ground
    Always
    10 kΩ or higher
    D39-3 (+) - Body ground
    Always
    10 kΩ or higher
    D39-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E247464E01
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E6-1 - E6-2
      Always
      3.4 to 4.6 Ω
      F9-1 - F9-2
      Always
      3.4 to 4.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E248904E02
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D39-1 (-) - D39-3 (+)
      Always
      3.4 to 4.6 Ω
      D39-4 (+) - D39-2 (-)
      Always
      10 kΩ or higher
      D39-3 (+)- D39-4 (+)
      Always
      Below 1 Ω
      D39-1 (-) - D39-2 (-)
      Always
      Below 1 Ω
      D66-1 (-) - D66-3 (+)
      Always
      3.4 to 4.6 Ω
      D66-4 (+) - D66-2 (-)
      Always
      10 kΩ or higher
      D66-3 (+) - D66-4 (+)
      Always
      Below 1 Ω
      D66-1 (-) - D66-2 (-)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
OK


4.INSPECT REAR SPEAKER ASSEMBLY


    E248921E01
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H24-1 - H24-2
      Always
      5.1 to 6.9 Ω
      G15-1 - G15-2
      Always
      5.1 to 6.9 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)