Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM

FRONT LOWER SUSPENSION ARM > REMOVAL

for Preparation Click here


HINT:
  1. The procedure listed below is for the LH side.
  2. Use the same procedure for the RH side and LH side.



1. REMOVE FRONT WHEEL


2. REMOVE REAR ENGINE UNDER COVER LH


    C256602
  1. Remove the 3 clips and rear engine under cover LH.



3. REMOVE LOWER ARM SUPPORT PLATE


    C256599
  1. Remove the bolt, nut and lower arm support plate.



4. SEPARATE TIE ROD END SUB-ASSEMBLY LH


    C257549
  1. Remove the cotter pin and nut.

  1. Install the SST (spacer B) to the tie rod assembly.

    NOTICE:
    As SST may get damaged, make sure the space between the tie rod and the spacers is not less than 1 mm (0.0394 in.).



  1. Using SST, disconnect the tie rod assembly.


    C259936E02


    Text in Illustration 
    *1
    Nut
    *2
    Body
    *3
    Claw
    *4
    SST (Spacer B)
    *a
    1 mm (0.0394 in.)
    *b
    Place a Wrench Here
    V100135
    Molybdenum Grease
    V100136
    Turn
    SST
    09960-20010   (09961-02010, 09961-02060)

    CAUTION:
    Apply the molybdenum grease to the end and threads of the SST bolt.

    NOTICE:
    1. Install SST so that the claw and body are parallel.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Do not damage the dust cover on the tie rod end sub-assembly.
    4. Do not damage the tie-rod end.
    5. Do not damage the ball joint dust cover.
    6. Do not damage the steering knuckle.



5. SEPARATE STEERING KNUCKLE LH


    C256600
  1. Remove the cotter pin and nut.

  1. Install the SST (spacer B) to the front lower suspension arm assembly LH.

    NOTICE:
    As SST may get damaged, make sure the space between the front lower suspension arm assembly LH and the spacers is not less than 1 mm (0.0394 in.).



  1. Using SST, disconnect the front lower suspension arm assembly LH.


    C256684E02


    Text in Illustration 
    *1
    Nut
    *2
    Body
    *3
    Claw
    *4
    SST (Spacer B)
    *a
    1 mm (0.0394 in.)
    *b
    Place a Wrench Here
    V100135
    Molybdenum Grease
    V100136
    Turn
    SST
    09960-20010   (09961-02010, 09961-02060)

    CAUTION:
    Apply the molybdenum grease to the end and threads of SST bolt.

    NOTICE:
    1. Install SST so that the claw and body are parallel.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Do not damage the dust cover on the front suspension lower arm assembly.
    4. Do not damage the front lower arm sub-assembly.
    5. Do not damage the front disc brake dust cover.
    6. Do not damage the steering knuckle.



6. REMOVE FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    C256601
  1. Remove the bolt, nut and front lower suspension arm assembly LH from the front cross member sub-assembly.



7. REMOVE FRONT LOWER SUSPENSION ARM BOLT


    C257514E02
  1. Using SST, remove the front lower suspension arm bolt.

    SST
    09726-18010