Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS



1. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)
  1. Customizing with the GTS

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Wireless Door Lock or Others.

    5. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock function / OFF or ON
      OFF or ON
      Main body ECU (network gateway ECU)
      Wireless Buzzer Resp*1
      ON
      Wireless door lock buzzer response
      OFF or ON
      Hazard Answer Back
      ON
      When wireless lock switch on transmitter pressed, illuminate all hazard warning lights once. When unlock switch pressed, all hazard warning lights illuminate twice
      OFF or ON
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Unlock 2 Operation*2, *3
      ON
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Panic Function*2
      ON
      Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 1.5 seconds
      OFF or ON
      Wireless Auto Lock*2
      ON
      This function turns the wireless auto lock function on or off.
      OFF or ON
      Auto Lock Time
      30 s*4 or 60 s*2
      This function controls amount of time from unlocking doors to automatic re-locking function.
      30 s, 60 s or 120 s
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the electrical key transmitter sub-assembly.
      1tim ON, 2tim ON, Long1 or Long2
      Wireless Buzzer Vol*1
      Level 5
      Wireless door lock buzzer volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0

      1. *1: w/ Wireless Door Lock Buzzer Answer-back Function
      2. *2: w/ Panic Alarm Control Function
      3. *3: w/ Double Locking System
      4. *4: w/o Panic Alarm Control Function

      Others 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Detection of Vehicle*
      ON
      This function turns the detection of vehicle function OFF or ON.
      OFF or ON
      Main body ECU (network gateway ECU)
      1. *: w/ Vehicle Position Sensing Function



2. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)
  1. Customizing with the GTS

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Record the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Wireless Door Lock or Warning.

    5. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Function
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock function / OFF or ON
      OFF or ON
      Main body ECU (network gateway ECU)
      Wireless Buzzer Resp*1
      ON
      Wireless door lock buzzer response
      OFF or ON
      Main body ECU (network gateway ECU)
      Hazard Answer Back
      ON
      When wireless lock switch on transmitter pressed, illuminate all hazard warning lights once. When unlock switch pressed, all hazard warning lights illuminate twice
      OFF or ON
      Main body ECU (network gateway ECU)
      Open Door Warning*2
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (network gateway ECU)
      Unlock 2 Operation*3, *4
      ON
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Main body ECU (network gateway ECU)
      Panic Function*3
      ON
      Function to operate theft deterrent system by continuously pressing panic switch on door control transmitter module set sub-assembly for 1.5 seconds
      OFF or ON
      Main body ECU (network gateway ECU)
      Wireless Auto Lock
      ON
      This function turns the wireless auto lock function on or off.
      OFF or ON
      Main body ECU (network gateway ECU)
      Auto Lock Time
      30 s
      Time until relocking after unlocking with wireless door lock function
      30 s, 60 s or 120 s
      Main body ECU (network gateway ECU)
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the door control transmitter module set sub-assembly.
      1tim ON, 2tim ON, Long1 or Long2
      Main body ECU (network gateway ECU)
      Wireless Buzzer Vol*1
      Level 5
      Wireless door lock buzzer volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0
      Main body ECU (network gateway ECU)

      1. *1: w/ Wireless Door Lock Buzzer Answer-back Function
      2. *2: w/ Door Ajar Warning Function
      3. *3: w/ Panic Alarm Control Function
      4. *4: w/ Double Locking System

      Others 
      Display
      Default
      Function
      Setting
      Relevant ECU
      Detection of Vehicle*
      ON
      This function turns the detection of vehicle function OFF or ON.
      OFF or ON
      Main body ECU (network gateway ECU)
      1. *: w/ Vehicle Position Sensing Function



3. CUSTOMIZE KEY REMINDER WARNING SYSTEM (w/o Entry and Start System)
  1. Customizing with the GTS

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Record the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Utility / Customize / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Function
      Setting
      Relevant ECU
      Key Remind Sound
      Normal
      Function to change cycle of the key reminder warning buzzer.
      Normal, Slow or Fast
      Combination meter assembly



4. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Entry & Start / Utility / Customize / Entry & Start or Warning.

    5. Select the setting by referring to the table below.

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Park Wait Time
      2.5s
      Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.
      0.5s, 1.5s, 2.5s or 5s
      Certification ECU (smart key ECU assembly)
      Trunk Open Mode
      ON
      Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the back door opener switch assembly.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function to Turn ON / OFF of the Engine Start Indicator.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Door Unlock Mode2
      Driver
      Function that chooses the doors to be operated by entry unlock operation.
      All or Driver
      Certification ECU (smart key ECU assembly)
      Touch Activation Over Threshold
      Active
      The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.
      Active or Not Active
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning
      ON
      Enables or disables the sounding of the buzzer when the key battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Key Left in Vehicle Buz
      ON
      Function to warn when left the electrical key transmitter sub-assembly in the vehicle.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      IG ON Key Out Warning
      ON
      Function to warn when carried out the electrical key transmitter sub-assembly from the vehicle of engine switch on (IG).
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the engine switch.


    1. The following functions are disabled when the entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Entry ignition function
      3. Key lock-in prevention function
      4. Entry back door open/lock function
      5. Entry warning functions

    2. Canceling the system operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver side door is closed.
        3. The driver side door is unlocked.
      2. Press the unlock switch of the electrical key transmitter sub-assembly.
      3. Open the driver side door within 5 seconds of completing the step above (driver side door: closed at beginning of step → opened).
      4. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Close and open the driver side door twice within 30 seconds of completing the above step (driver side door: open at beginning of step → closed → opened → closed → opened).
      6. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 30 seconds of completing the step above.

        NOTICE:
        If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      7. Close and open the driver side door within 30 seconds of completing the step above (driver side door: open at beginning of step → closed → opened).
      8. Close the driver side door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

    3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



5. CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)
  1. Customizing with the GTS

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current setting before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The items in the table below can be customized.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Entry & Start / Utility / Customize / Entry & Start or Warning.

    5. Select the setting by referring to the table below.

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function to Turn ON / OFF of the Engine Start Indicator.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning
      ON
      Function that enables or disables the sounding of the buzzer when the key battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the engine switch.


    1. The following functions are disabled when the entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Entry ignition function
      3. Key lock-in prevention function
      4. Entry back door open/lock function
      5. Entry warning functions

    2. Canceling the system operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver side door is closed.
        3. The driver side door is unlocked.
      2. Press the unlock switch of the electrical key transmitter sub-assembly.
      3. Open the driver side door within 5 seconds of completing the step above (driver side door: closed at beginning of step → opened).
      4. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Close and open the driver side door twice within 30 seconds of completing the above step (driver side door: open at beginning of step → closed → opened → closed → opened).
      6. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 30 seconds of completing the step above.

        NOTICE:
        If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      7. Close and open the driver side door within 30 seconds of completing the step above (driver side door: open at beginning of step → closed → opened).
      8. Close the driver side door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

    3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



6. CUSTOMIZE THEFT DETERRENT SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Security.

    5. Select the setting by referring to the table below.

      Security 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Security System
      OFF
      This function operates the theft deterrent system
      ON or OFF
      Main Body ECU (Network Gateway ECU)

  1. Theft deterrent system cancel function (manual operation)

    1. Performing the theft deterrent system cancellation setting allows the theft deterrent system to be stopped.

    2. Configuring the theft deterrent system cancellation setting

      1. Set the vehicle in the following state.
        1. Disarm the theft deterrent system.
      2. After setting the vehicle in the above state, perform the following operations.
      3. Close all doors and turn the engine switch on (IG).
      4. When the above operations are complete, push down and hold the unlock switch on the door control switch, open the driver side door and hold it for 10 seconds.
      5. When the above operations are complete, the horn sounds twice and "AL OF" appears on the multi-display in the combination meter assembly, informing the operator that the theft deterrent system cancellation setting is complete.

    3. Returning the theft deterrent system from canceled to normal mode.

      1. Perform the theft deterrent system cancellation setting again.
      2. When the above operations are complete, the horn sounds once and "AL ON" appears on the multi-display in the combination meter assembly, informing the operator that the normal mode setting has been resumed.

        HINT:
        1. Each time the cancellation is performed manually, the state changes between canceled and active alternately.
        2. When changing from active to canceled state, the horn sounds twice and "AL OF" appears on the multi-display in the combination meter assembly, and when changing from canceled to active state, the horn sounds once and "AL ON" appears on the multi-display in the combination meter assembly, in order to inform the operator of the alarm status.



7. CUSTOMIZE LIGHTING SYSTEM (INT)
  1. Customizing using the GTS

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ACC or ON.)
      7.5 s, 15 s or 30 s
      Main body ECU (Network gateway ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2 and map light when the ignition switch is turned from ACC or ON to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2 and map light when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Room Light when Aprchd*1
      ON
      Lights up the engine switch illumination and map light when a key enters any actuation area around the doors.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2 and map light when the illuminated entry function is operating.
      ON or OFF

      1. *1: w/ Entry and Start System
      2. *2: w/o Entry and Start System



8. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Combination Meter / Warning.

    5. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Warning 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Key Remind Sound
      NORMAL
      Function to change the frequency of the key reminder buzzer.
      NORMAL, FAST or SLOW
      Combination meter assembly
      Tail Remind Buzzer
      ON
      Function to change the Tail Remind Buzzer.
      ON or OFF
      Combination meter assembly
      Driver Side Seatbelt Warning Buzzer*
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*
      ON
      Function to change the seat-belt warning buzzer.
      ON or OFF
      Combination meter assembly
      1. *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

    6. Connect the GTS to the DLC3.

    7. Turn the ignition switch to ON.

    8. Turn the GTS on.

    9. Enter the following menus: Customize Setting / Combination Meter / Air Conditioner.

    10. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Ambient Temperature Adjustment
      0C (0F)
      Function to change the display temperature to match the actual temperature.
      +3C (+5.4F) +2C (+3.6F), +1C (+1.8F), 0C (0F), -1C (-1.8F), -2C (-3.6F) or 3C (-5.4F)
      Combination meter assembly



9. CUSTOMIZE SEAT BELT WARNING SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.
  4. These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer
      ON
      Function to sound the driver seat belt warning buzzer
      ON/OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer
      ON
      Function to sound the front passenger seat belt warning buzzer
      ON/OFF

      HINT:
      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.



10. CUSTOMIZE AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
  1. Customizing with the GTS

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the GTS.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Air Conditioner.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Air Inlet Mode
      Automatic
      In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      Automatic or Manual
      Air Conditioning Control Assembly
      Compressor Mode
      Automatic
      Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF
      Automatic or Manual
      Air Conditioning Control Assembly
      Compressor/Air Inlet DEF Operation
      LINK
      Function to automatically turn the A/C on linked with the FRONT DEF button when the A/C is off
      NORMAL or LINK
      Air Conditioning Control Assembly
      DEF (PSW/Lock) Mode Setting
      Link
      In case of the compressor LOCK or pressor switch ON, this is the function to change the mode automatically to Fresh mode
      NORMAL or LINK
      Air Conditioning Control Assembly
      Foot/DEF Automatic Blow Up Function
      ON
      Function to increase the blower level automatically when the defroster is ON
      ON or OFF
      Air Conditioning Control Assembly
      Foot/DEF Auto Mode
      Automatic
      Function to turn the airflow from FOOT/DEF ON automatically when AUTO MODE is ON
      Automatic or Manual
      Air Conditioning Control Assembly
      Set Temperature Shift
      0°C
      Function to perform control with the shifted temperature versus the displayed temperature
      -3°C,-2°C, -1°C, 0°C, +1°C, +2°C, +3°C
      Air Conditioning Control Assembly



11. CUSTOMIZE WINDOW DEFOGGER SYSTEM
  1. Customizing using the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Air Conditioner.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Rear Defogger
      Normal
      Drive mode setting for rear window defogger operation
      Normal*1 / Continuance*2
      Main Body ECU (Network Gateway ECU)

      1. *1: Rear defogger operation turned off after approximately 15 minutes
      2. *2: Rear defogger operate the rear window defogger operates for approximately 15 minutes and stops for 2 minutes, and that these operations repeat.



12. CUSTOMIZE LIGHTING SYSTEM (EXT)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Light Control.

    5. Select the setting by referring to the table below.

      Light Control 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Response Time*1
      Normal
      Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position.
      Normal or Long
      Main Body ECU (Network Gateway ECU)
      Light Auto OFF Delay*1
      30 s
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      OFF, 30 s, 60 s or 90 s
      Follow Me Home Lighting Time*2
      30 s
      Changes the low beam headlight lighting time when ignition switch is off and dimmer switch is pulled to flash headlights once.
      30 s, 60 s, 90s, or 120s

      HINT:
      Items for which there are no settings do not appear on the GTS, or do not operate.

      1. *1: w/ Automatic Light Control System
      2. *2: w/ Follow Me Home System