Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

DTC    B2275    STSW Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a circuit malfunction is detected in the engine start permission signal output circuit inside the certification ECU (smart key ECU assembly), or when an abnormal external engine start permission signal is detected.

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2275
  1. Circuit malfunction detected in the engine start permission output circuit inside the certification ECU (smart key ECU assembly) (1-trip detection logic*).
  2. External engine start permission signal malfunction (1-trip detection logic*).
  1. Certification ECU (smart key ECU assembly)
  2. SFI system
  3. Wire harness or connector
Engine start operation is performed.
  1. *: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The engine cannot be started.
-

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2275
-
-

WIRING DIAGRAM


B312733E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  5. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ECM)
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A33 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Connection
    Specified Condition
    D48-7 (STSW) - A33-17 (STSW)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D48-7 (STSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Reconnect the A33 ECM connector.



    B268627E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Condition
    Connection
    Specified Condition
    D48-7 (STSW) - D48-11 (GND)
    With the brake pedal*1 or clutch pedal*2 depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off)
    2 V or less → 9 V or higher

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission
    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)