Home › Drivetrain ยท TL70 MANUAL TRANSMISSION / TRANSAXLE › COUNTER GEAR

COUNTER GEAR > INSPECTION

for Preparation Click here



1. INSPECT NO. 2 TRANSMISSION HUB SLEEVE


    C257080
  1. Check that the spline gear edges of the No. 2 transmission hub sleeve are not worn down.

    HINT:
    If it shows any sign of wear, replace the No. 2 transmission hub sleeve with a new one.

  1. Install the No. 2 transmission hub sleeve to the No. 2 transmission clutch hub, and then check that it slides smoothly.

    HINT:
    If it does not slide smoothly, replace the No. 2 transmission hub sleeve and No. 2 transmission clutch hub with a new one.



2. INSPECT NO. 2 TRANSMISSION HUB SLEEVE CLEARANCE


    C257047
  1. Using a vernier caliper, measure the claw width of the No. 2 gear shift fork.

    Standard width:
    7.9 to 8.0 mm (0.311 to 0.315 in.)

    Minimum width:
    7.9 mm (0.311 in.)

    HINT:
    If the width is less than the minimum, replace the No. 2 gear shift fork with a new one.

  1. Using a vernier caliper, measure the groove of the No. 2 transmission hub sleeve, and then calculate the clearance with the No. 2 gear shift fork.

    Standard clearance:
    0.15 to 0.35 mm (0.00590 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    HINT:
    If the clearance exceeds the maximum, replace both the No. 2 gear shift fork and No. 2 transmission hub sleeve with a new ones.



3. INSPECT NO. 1 SYNCHRONIZER RING


    C257104
  1. Apply manual transmission gear oil to the taper cone of the counter shaft 4th gear, and then hold the No. 1 synchronizer ring in position with your hand to measure the clearance between the No. 1 synchronizer ring and counter shaft 4th gear by using a feeler gauge.

    Standard clearance:
    0.8 to 1.6 mm (0.0314 to 0.0629 in.)

    Maximum clearance:
    1.6 mm (0.0629 in.)

    NOTICE:
    Check the entire circumference of the gear.

    HINT:
    If the clearance exceeds the maximum, replace the No. 1 synchronizer ring with a new one.



    C257105
  1. Apply manual transmission gear oil to the taper cone of the counter shaft 4th gear, and then hold the No. 1 synchronizer ring in position with your hand to check that it does not slide in the circumferential direction.

    HINT:
    If the ring slides, replace the No. 1 synchronizer ring with a new one.



4. INSPECT NO. 3 SYNCHRONIZER RING SET


  1. Apply manual transmission gear oil to the taper cone of the counter shaft 3rd gear and No. 3 synchronizer ring set, and then hold the No. 3 synchronizer ring set in position with your hand to measure the clearance between the No. 3 synchronizer ring set and the counter shaft 3rd gear by using a feeler gauge.


    C266880E01


    Text in Illustration 
    *a
    Inner
    *b
    Middle
    *c
    Outer
    -
    -

    Standard Clearance:

    Location
    Standard clearance mm (in.)
    Inner
    0.4 to 1.2 (0.0157 to 0.0472)
    Middle
    0.3 to 1.3 (0.0118 to 0.0512)
    Outer
    0.8 to 1.8 (0.0315 to 0.0709)

    NOTICE:
    Check the entire circumference of the gear.

    HINT:
    If the result is not as specified, replace the No. 3 synchronizer ring set with a new one.



    C266881
  1. Apply manual transmission gear oil to the taper cone of the counter shaft 3rd gear, and then hold the No. 3 synchronizer ring set in position with your hand to check that it does not slide in the circumferential direction.

    HINT:
    If the No. 3 synchronizer ring set slides, replace the No. 3 synchronizer ring set with a new one.



5. INSPECT COUNTER SHAFT


    C257106E01
  1. Using a micrometer, measure the outer diameter of each location.

    Standard Outer Diameter:
    Part
    Standard outer diameter mm (in.)
    Minimum outer diameter mm (in.)
    A
    39.284 to 39.300 (1.54661 to 1.54721)
    39.284 (1.54661)
    B
    37.984 to 38.000 (1.49543 to 1.49606)
    37.984 (1.49543)
    C
    24.987 to 25.000 (0.98374 to 0.98425)
    24.987 (0.98374)

    HINT:
    If the diameter is less than the minimum, replace the counter shaft with a new one.



    C257107
  1. Using V-block and a dial gauge, measure the runout of each location as shown in the illustration.

    Standard runout:
    0.03 mm (0.00118 in.) or less

    HINT:
    If the runout exceeds the standard, replace the counter shaft with a new one.



6. INSPECT COUNTER SHAFT 3RD GEAR


    C257108
  1. Using a cylinder gauge, measure the inside diameter of the counter shaft 3rd gear.

    Standard inside diameter:
    43.015 to 43.040 mm (1.69350 to 1.69448 in.)

    Maximum inside diameter:
    43.040 mm (1.69448 in.)

    HINT:
    If the inside diameter exceeds the maximum, replace the counter shaft 3rd gear with a new one.



7. INSPECT COUNTER SHAFT 4TH GEAR


    C257108
  1. Using a cylinder gauge, measure the inside diameter of the counter shaft 4th gear.

    Standard inside diameter:
    46.315 to 46.340 mm (1.82425 to 1.82441 in.)

    Maximum inside diameter:
    46.340 mm (1.82441 in.)

    HINT:
    If the inside diameter exceeds the maximum, replace the counter shaft 4th gear with a new one.



8. REMOVE 4TH GEAR BEARING INNER RACE


    C257109
  1. Using a micrometer, measure the outside diameter of the 4th gear bearing inner race.

    Standard outside diameter:
    46.225 to 46.250 mm (1.81988 to 1.82087 in.)

    Minimum outside diameter:
    46.225 mm (1.81988 in.)

    NOTICE:
    Do not measure the oil groove.

    HINT:
    If the outside diameter is less than the minimum, replace the 4th gear bearing inner race with a new one.