Home › Vehicle Exterior › BODY WELD POINT › FRONT DOOR OUTER PANEL
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295208 FRONT DOOR OUTER PANEL F

BODY WELD POINT  FRONT DOOR OUTER PANEL  ASSEMBLY REPLACEMENT  


K102426

REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.
K108832

Brazing or Arc Brazing for Removal


REMOVAL POINT
1.

Before removing the outer panel, mark the installation position with tape.

2.

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.

3.

After grinding off the hemming location, remove the outer panel.


K137049E01
4.635,0.802 4.917,0.417 4.917,0.417 5.083,0.417 false 3.979,7.917 4.25,8.25 4.25,8.25 4.417,8.25 false 3.094,0.896 4.354,1.385 1.26,0.49 10 false Installation Position 5.146,0.333 6.198,0.885 1.052,0.552 10 false Positioning Tape 3.74,6.427 5,6.917 1.26,0.49 10 false Hemming Location 4.49,8.167 5.333,8.667 0.844,0.5 10 false Disc Sander

INSTALLATION


Symbol Meaning
K108830

Fillet Weld
K108832

Braze
K108833

Spot MIG Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem about 30° with a hammer and dolly. Then, fasten tightly with a hemming tool.

HINT:
·

Perform hemming in three steps, being careful not to warp the panel.

·

If a hemming tool cannot be used, hem with a hammer and dolly.



3.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K137050E01
3.583,1.333 3.833,1 3.833,1 4,1 false 1.875,4.292 1.875,3.542 false 5.469,5.469 5.583,5.083 5.583,5.083 5.75,5.083 false 5.833,5.656 6,5.5 6,5.5 6.167,5.5 false 5.948,6.229 6.083,6.5 6.083,6.5 6.25,6.5 false 5.615,8.208 5.833,8.417 5.833,8.417 6,8.417 false 0.208,1.271 0.813,1.677 0.604,0.406 10 false 20 (0.79) 0.948,1.167 2.25,1.417 1.302,0.25 10 false 5 (0.20) 4.083,0.917 5.188,1.375 1.104,0.458 10 false Positioning Tape 4.813,1.792 5.417,2.198 0.604,0.406 10 false 10 (0.39) 3.667,2.469 4.271,2.875 0.604,0.406 10 false 10 (0.39) 6.052,3.458 6.75,4 0.698,0.542 10 false Drain Hole 0.958,4.323 2.958,4.781 2,0.458 10 false FRONT DOOR PANEL OUTER 0.177,7.083 0.781,7.49 0.604,0.406 10 false 5 (0.20) 3.813,7.094 4.417,7.5 0.604,0.406 10 false 5 (0.20) 5.833,5 6.677,5.219 0.844,0.219 10 false Dolly 6.25,5.417 7.094,5.823 0.844,0.406 10 false Cloth Tape 6.323,6.417 7.094,6.667 0.771,0.25 10 false Hammer 4.885,6.01 5.271,6.406 0.385,0.396 10 false 30° 6.083,8.323 7.094,8.76 1.01,0.438 10 false Hemming Tool 0.26,8.427 0.823,8.865 0.563,0.438 10 false mm (in.)