Home › Vehicle Exterior › BODY WELD POINT › REAR DOOR OUTER PANEL
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295209 REAR DOOR OUTER PANEL F

BODY WELD POINT  REAR DOOR OUTER PANEL  ASSEMBLY REPLACEMENT  


K102427

REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.
K108832

Brazing or Arc Brazing for Removal


REMOVAL POINT
1.

Before removing the outer panel, mark the installation position with tape.

2.

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.

3.

After grinding off the hemming location, remove the outer panel.


K137051E01
2.604,0.896 2.25,0.167 2.25,0.167 2.417,0.167 false 3.979,8.042 4.25,8.333 4.25,8.333 4.417,8.333 false 2.5,0.073 4.948,0.271 2.448,0.198 10 false Positioning Tape 2.906,0.99 4.531,1.292 1.625,0.302 10 false Installation Position 3.75,6.5 5.375,6.802 1.625,0.302 10 false Hemming Location 4.49,8.24 6.115,8.542 1.625,0.302 10 false Disc Sander

INSTALLATION


Symbol Meaning
K108830

Fillet Weld
K108832

Braze
K108833

Spot MIG Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem about 30° with a hammer and dolly. Then, fasten tightly with a hemming tool.

HINT:
·

Perform hemming in three steps, being careful not to warp the panel.

·

If a hemming tool cannot be used, hem with a hammer and dolly.



3.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K137052E01
1.385,1.188 1,0.333 1,0.333 1.167,0.333 false 1.917,4.167 1.917,3.417 false 5.5,5.052 5.583,4.667 5.583,4.667 5.75,4.667 false 5.823,5.219 6.083,5 6.083,5 6.25,5 false 5.938,5.813 6.115,6.01 6.115,6.01 6.281,6.01 false 5.594,7.792 5.771,7.99 5.771,7.99 5.938,7.99 false 1.25,0.25 3.698,0.448 2.448,0.198 10 false Positioning Tape 0.458,1.115 1.042,1.552 0.583,0.438 10 false 10 (0.39) 3.854,1.052 4.438,1.49 0.583,0.438 10 false 10 (0.39) 4.823,1.542 5.406,1.979 0.583,0.438 10 false 10 (0.39) 6.052,3.188 6.802,3.635 0.75,0.448 10 false Drain Hole 1.042,4.208 2.958,4.708 1.917,0.5 10 false REAR DOOR PANEL OUTER 0.417,5.781 1,6.219 0.583,0.438 10 false 10 (0.39) 0.302,7.385 0.885,7.823 0.583,0.438 10 false 5 (0.20) 3.708,7.896 4.292,8.333 0.583,0.438 10 false 5 (0.20) 0.25,8.427 0.833,8.865 0.583,0.438 10 false mm (in.) 5.833,4.583 6.583,4.771 0.75,0.188 10 false Dolly 6.344,4.906 7.094,5.344 0.75,0.438 10 false Cloth Tape 6.385,5.927 7.135,6.365 0.75,0.438 10 false Hammer 6.01,7.906 7.01,8.406 1,0.5 10 false Hemming Tool 4.833,5.583 5.167,6 0.333,0.417 10 false 30°