Home › Vehicle Exterior › BODY WELD POINT › QUARTER PANEL
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295212 QUARTER PANEL F

BODY WELD POINT  QUARTER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K102431

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

*1 in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K137061E01
3.583,7.25 3.5,7.25 3.5,7.25 3.552,7.021 false 0.333,0.333 0.885,0.573 0.552,0.24 12 false LH: 0.448,0.896 1.083,1.292 0.635,0.396 10 false 60 (2.36) 3.833,0.948 4.469,1.344 0.635,0.396 10 false 35 (1.38) 3.615,7.156 3.927,7.354 0.313,0.198 10 false *1 0.25,8.469 0.885,8.865 0.635,0.396 10 false mm (in.)

K137062E01
0.333,0.333 0.885,0.573 0.552,0.24 12 false LH:

K137063E01
3.75,7.25 3.833,7.25 3.833,7.25 3.76,7.031 false 0.333,0.333 0.885,0.573 0.552,0.24 12 false RH: 2.938,0.979 3.521,1.396 0.583,0.417 10 false 35 (1.38) 6.333,0.917 6.917,1.333 0.583,0.417 10 false 60 (2.36) 0.25,8.448 0.833,8.865 0.583,0.417 10 false mm (in.) 3.563,7.156 3.979,7.323 0.417,0.167 10 false *1

K137064E01
0.333,0.333 0.885,0.573 0.552,0.24 12 false RH:


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the quarter panel, door lock striker retainer subassembly and fuel inlet box with the standard number of welding points.

5.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even continuous bead.


6.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



7.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *1 in the illustration.

HINT:

Apply enough adhesive for the panels to stick to each other.


8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K137065E01
5.135,1.531 5.5,1.25 5.5,1.25 5.667,1.25 false 2,2.333 2.563,2.104 false 1.833,2.333 2,2.333 2,2.333 2.688,2.229 false 2.5,3.333 2.667,3.333 2.667,3.333 2.521,2.333 false 2.417,7.583 2.333,7.917 2.333,7.917 2.5,7.917 false 0.333,0.333 0.885,0.573 0.552,0.24 12 false LH: 2.906,1.333 3.5,1.729 0.594,0.396 10 false 60 (2.36) 3.906,1.438 4.5,1.635 0.594,0.198 10 true 35 (1.38) 5.771,1.167 7.031,1.594 1.26,0.427 10 false QUARTER PANEL 1.625,2.24 1.938,2.438 0.313,0.198 10 false *1 0.24,3.24 2.417,3.906 2.177,0.667 10 false DOOR LOCK STRIKER RETAINER SUB-ASSEMBLY 5.385,7.573 5.979,7.969 0.594,0.396 10 false 5 (0.20) 2.563,7.813 2.875,8.01 0.313,0.198 10 false *1 0.313,8.448 0.885,8.865 0.573,0.417 10 false mm (in.)

K137066E01
0.333,0.333 0.885,0.573 0.552,0.24 12 false LH:

K137067E01
4.667,1.813 5.167,2.083 5.167,2.083 5.333,2.083 false 4.542,1.948 5.167,2.083 false 1.583,0.917 1.75,0.917 1.75,0.917 2.083,1.25 false 1.75,2.75 1.917,2.75 1.917,2.75 2.49,3.135 false 4.677,2.052 4.583,3.083 4.583,3.083 4.75,3.083 false 5.635,5.073 5.167,4.417 5.167,4.417 5.333,4.417 false 5.677,5.708 5.167,4.417 false 6.667,5.771 6.833,6.25 6.833,6.25 6.667,6.25 false 3.552,8.156 3.667,8.417 3.667,8.417 3.583,8.417 false 0.333,0.333 0.885,0.573 0.552,0.24 12 false RH: 0.375,0.833 1.594,1.333 1.219,0.5 10 false QUARTER PANEL 0.563,2.667 1.781,3.167 1.219,0.5 10 false FUEL INLET BOX 2.698,1.156 3.281,1.344 0.583,0.188 10 true 35 (1.38) 3.75,1.094 4.354,1.458 0.604,0.365 10 false 60 (2.36) 5.385,1.979 5.698,2.177 0.313,0.198 10 false *1 4.844,3 7.01,3.667 2.167,0.667 10 false DOOR LOCK STRIKER RETAINER SUB-ASSEMBLY 5.417,4.333 5.969,4.75 0.552,0.417 10 false RIVETS 4.844,6.167 6.615,6.833 1.771,0.667 10 false FUEL FILLER OPENING LID SUB-ASSEMBLY 6.188,7.49 6.74,7.906 0.552,0.417 10 false 5 (0.20) 3.385,8.323 3.698,8.521 0.313,0.198 10 false *1 0.25,8.448 0.802,8.865 0.552,0.417 10 false mm (in.)

K137068E01
0.333,0.333 0.885,0.573 0.552,0.24 12 false RH: