Home › Vehicle Exterior › BODY WELD POINT › FIT STANDARD / ADJUSTMENT METHOD › 2011.11–2015.08
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295227 FIT STANDARD / ADJUSTMENT METHOD F

BODY WELD POINT  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B290261C02
1.073,2.469 1.417,2.771 0.344,0.302 10 *A 2.583,3.719 2.927,4.021 0.344,0.302 10 *B 3.052,0.51 3.573,0.813 0.521,0.302 10 *a 5.625,2.427 5.979,2.74 0.354,0.313 10 *b 5.823,3 6.125,3.302 0.302,0.302 10 *c 4.906,2.958 5.198,3.198 0.292,0.24 10 *d 1.646,2.583 1.938,2.865 0.292,0.281 10 *e 1.698,3.333 1.958,3.635 0.26,0.302 10 *f 3.271,3.823 3.594,4.104 0.323,0.281 10 *g 3.333,4.635 3.635,4.885 0.302,0.25 10 *h
*A Standard Type *B Aero Type


Standard:
Area Measurement Area Measurement
*a 8.0 mm
(0.315 in.)
*b 2.0 to 5.0 mm
(0.079 to 0.197 in.)
*c -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
*d 6.9 mm
(0.272 in.)
*e 4.2 to 7.2 mm
(0.165 to 0.284 in.)
*f 1.2 to 4.2 mm
(0.047 to 0.165 in.)
*g 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*h 1.3 to 4.3 mm
(0.051 to 0.169 in.)


HINT:

Centering bolts are used to mount the hood hinge and the hood lock. The hood and the hood lock cannot be adjusted with the centering bolts in. Substitute standard bolts (with flange) for the centering bolts when making adjustments.




ADJUST HOOD SUB-ASSEMBLY


a.
B161310

Loosen the 4 hood side hinge bolts.


b.

Move the hood to adjust the clearance to within the standard range.


c.

Tighten the 4 hood side hinge bolts after the adjustment.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


d.
B290263

Adjust the height of the hood front end by turning the 2 center hood cushions.

HINT:

The center hood cushion can be raised and lowered by turning it.



e.

Adjust the hood lock.

i.

Remove the front bumper cover.


ii.

Remove the No. 1 hood lock control cable cover. (for RHD)


iii.

Remove the No. 2 hood lock control cable cover. (for LHD)


iv.
B297765

Loosen the 3 bolts.


v.
B297766

Adjust the hood lock position so that the striker can enter it smoothly.


vi.

Tighten the 3 bolts after the adjustment.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)



f.
B290263

Adjust the operating force to close the hood by turning the 2 center hood cushions as shown in the illustration.

HINT:

The center hood cushion can be raised and lowered by turning it.




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements are within the standard ranges.

B297790N01
6.427,0.823 6.74,1.125 0.313,0.302 10 *a 5.802,0.604 6.083,0.844 0.281,0.24 10 *b 4.104,0.5 4.365,0.781 0.26,0.281 10 *c 4.438,1 4.729,1.26 0.292,0.26 10 *d 2.625,0.531 2.906,0.792 0.281,0.26 10 *c 2.885,1.125 3.167,1.385 0.281,0.26 10 *d 0.958,1.49 1.281,1.75 0.323,0.26 10 *c 1.521,1.719 1.823,1.99 0.302,0.271 10 *e 0.375,4.281 0.656,4.552 0.281,0.271 10 *f 1,4.094 1.323,4.365 0.323,0.271 10 *g 2.906,4.677 3.198,4.958 0.292,0.281 10 *i 2.781,5.01 3.052,5.25 0.271,0.24 10 *h 4.458,4.646 4.729,4.917 0.271,0.271 10 *j 4.323,4.948 4.615,5.219 0.292,0.271 10 *h 5.844,4.354 6.135,4.656 0.292,0.302 10 *g 6.458,4.51 6.729,4.781 0.271,0.271 10 *k

Standard:
Area Measurement Area Measurement
*a 3.6 to 6.6 mm
(0.201 to 0.260 in.)
*b -1.6 to 1.4 mm
(-0.063 to 0.055 in.)
*c 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*d 5.9 to 8.9 mm
(0.232 to 0.350 in.)
*e 7.5 to 10.5 mm
(0.295 to 0.413 in.)
*f 3.5 to 6.5 mm
(0.138 to 0.256 in.)
*g -1.5 to 1.5 mm
(-0.059 to 0.059 in.)
*h 4.5 to 7.5 mm
(0.177 to 0.295 in.)
*i 5.5 to 8.5 mm
(0.217 to 0.335 in.)
*j 4.8 to 7.8 mm
(0.189 to 0.307 in.)
*k 3.5 to 6.5 mm
(0.138 to 0.256 in.)
- -


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures described below are for the RH side.

·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with flange) for the centering bolts when making adjustments.





ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH


a.
B297791

Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

SST
09812-00010  


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.
B297792

Adjust the door horizontally and vertically by loosening the door side hinge bolts.


d.

Tighten the door side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.
B297793

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Tighten the striker mounting screws after the adjustment.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)



INSPECT REAR DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements are within the standard ranges.

B297810N01
0.719,0.729 1.063,1.01 0.344,0.281 10 *f 1.354,0.948 1.667,1.208 0.313,0.26 10 *e 4.208,0.406 4.573,0.688 0.365,0.281 10 *c 4.729,0.917 5.01,1.146 0.281,0.229 10 *d 5.458,0.938 5.854,1.229 0.396,0.292 10 *b 6.271,0.531 6.573,0.792 0.302,0.26 10 *a 6.26,3.417 6.583,3.708 0.323,0.292 10 *h 6.76,3.656 7.052,3.917 0.292,0.26 10 *k 5.177,4.427 5.448,4.667 0.271,0.24 10 *h 5.625,4.938 5.875,5.156 0.25,0.219 10 *k 3.99,4.771 4.302,5.073 0.313,0.302 10 *j 3.844,5.063 4.177,5.365 0.333,0.302 10 *i 1.26,4.427 1.573,4.708 0.313,0.281 10 *h 1.833,4.615 2.219,4.938 0.385,0.323 10 *g

Standard:
Area Measurement Area Measurement
*a 6.2 to 9.2 mm
(0.244 to 0.362 in.)
*b 5.1 to 8.1 mm
(0.201 to 0.319 in.)
*c 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*d 7.1 to 10.1 mm
(0.280 to 0.398 in.)
*e 3.6 to 6.6 mm
(0.142 to 0.260 in.)
*f -1.6 to 1.4 mm
(0.063 to 0.055 in.)
*g 3.5 to 6.5 mm
(0.138 to 0.256 in.)
*h -1.5 to 1.5 mm
(0.059 to 0.059 in.)
*i 4.5 to 7.5 mm
(0.177 to 0.295 in.)
*j 5.0 to 8.0 mm
(0.197 to 0.315 in.)
*k 3.0 to 6.0 mm
(0.118 to 0.236 in.)
- -


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures described below are for the RH side.

·

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with flange) for the centering bolts when making adjustments.





ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH


a.
B297811

Adjust the door horizontally and vertically by loosening the body side hinge bolts.


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.
B312697

Adjust the door horizontally and vertically by loosening the door side hinge bolts.


d.

Tighten the door side hinge bolts after the adjustment.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.
B297813

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Tighten the striker mounting screws after the adjustment.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)



INSPECT BACK DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B290325N01
4.646,0.417 5.042,0.792 0.396,0.375 10 *a 5.281,0.542 5.781,1.021 0.5,0.479 10 *b 6.146,2.365 6.479,2.688 0.333,0.323 10 *c 0.854,3.75 1.24,4.094 0.385,0.344 10 *c 6.042,4.021 6.448,4.365 0.406,0.344 10 *d 5.594,4.313 5.917,4.646 0.323,0.333 10 *e 0.479,1.833 0.906,2.208 0.427,0.375 10 *f 1.063,1.375 1.469,1.75 0.406,0.375 10 *g

Standard:
Area Measurement Area Measurement
*a 6.0 to 9.0 mm
(0.236 to 0.354 in.)
*b -0.5 to 2.5 mm
(-0.020 to 0.098 in.)
*c 4.0 to 7.0 mm
(0.158 to 0.276 in.)
*d 5.0 to 8.0 mm
(0.197 to 0.315 in.)
*e 24.3 to 27.3 mm
(0.957 to 1.075 in.)
*f 4.3 to 7.3 mm
(0.169 to 0.287 in.)
*g -1.3 to 1.7 mm
(-0.051 to 0.067 in.)
- -


HINT:

Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with flange) for the centering bolts when making adjustments.




ADJUST BACK DOOR PANEL SUB-ASSEMBLY


a.
B290327

Adjust the door position.

i.

Vertically adjust the door by loosening the door side hinge bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.
B290326

Horizontally adjust the door by loosening the door side hinge nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



b.
B290328

Adjust the striker position.

i.

Adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.


ii.

Tighten the striker mounting bolts after the adjustment.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)