Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING OR REPLACING PARTS › 2011.11–2015.08
BM19Y0E _V1 General _060205 INTRODUCTION _0295247 WHEN REMOVING,INSTALLING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


MEASURE VEHICLE HEIGHT


C245921N01
0.208,2.125 0.677,2.521 0.469,0.396 10 B 1.26,2.094 1.625,2.5 0.365,0.406 10 A 3.115,2.052 3.406,2.479 0.292,0.427 10 C 2.021,2.115 2.469,2.542 0.448,0.427 10 D 0.333,0.667 0.813,1.073 0.479,0.406 10 B 1.708,0.635 2.115,1.115 0.406,0.479 10 A 3.052,3.24 3.365,3.74 0.313,0.5 10 C 1.469,3.25 1.896,3.719 0.427,0.469 10 D

Vehicle Height (Unloaded Vehicle)
Tire Size Engine Front A-B Rear C-D
185/70 R14 K3-VE 45.5 mm
(1.79 in.)
47.1 mm
(1.85 in.)
185/65 R15 3SZ-VE 45.5 mm
(1.79 in.)
46.9 mm
(1.85 in.)

Measuring points:
A:

Ground clearance of front wheel center

B:

Ground clearance of front lower suspension arm set front bolt center

C:

Ground clearance of rear wheel center

D:

Ground clearance of lower control arm set bolt center


NOTICE:
·

Before inspecting the wheel alignment, check the vehicle height.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



HINT:

Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.



INSPECT WHEEL ANGLE


a.
C132439C02
0.563,0.146 1.021,0.531 0.458,0.385 10 *a 2.781,0.167 3.198,0.604 0.417,0.438 10 *a 2.427,0.167 2.885,0.594 0.458,0.427 10 *b 0.896,0.146 1.354,0.594 0.458,0.448 10 *b
*a Inside
*b Outside
V100135

Front of the Vehicle


Fully turn the steering wheel left and right, and measure the wheel turning angle.

Wheel Turning Angle (Unloaded Vehicle)
Tire Size Engine Inside Wheel Outside Wheel
185/70 R14 K3-VE 43°30' +/- 2°
(43.50° +/- 2°)
37°36' +/- 2°
(37.60° +/- 2°)
185/65 R15 3SZ-VE 43°30' +/- 2°
(43.50° +/- 2°)
37°36' +/- 2°
(37.60° +/- 2°)

If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.



INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


C132440C04
2.406,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.906,0.708 1.031,0.708 1.031,0.708 1.031,1.479 false 0.708,0.615 1.271,1.031 0.563,0.417 10 *1 2.781,0.729 3.333,1.208 0.552,0.479 10 *2
*1 Alignment tester
*2 Camber-Caster-Steering Axis Inclination Gauge


a.

Put the front wheel on the center of the alignment tester.


b.

Remove the wheel cap.


c.

Set the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.


d.

Inspect the camber, caster and steering axis inclination.

Camber Inclination (Unloaded Vehicle)
Tire Size Engine Camber
185/70 R14 K3-VE 0°30' +/- 45'
(0.5° +/- 0.75°)
185/65 R15 3SZ-VE 0°30' +/- 45'
(0.5° +/- 0.75°)

Caster Inclination (Unloaded Vehicle)
Tire Size Engine Caster
185/70 R14 K3-VE 5°05' +/- 1°
(5.08° +/- 1°)
185/65 R15 3SZ-VE 5°05' +/- 1°
(5.08° +/- 1°)

Steering Axis Inclination (Unloaded Vehicle)
Tire Size Engine Steering Axis Inclination
(Reference)
185/70 R14 K3-VE 12°45' +/- 1°
(12.75°)
185/65 R15 3SZ-VE 12°45' +/- 1°
(12.75°)

NOTICE:
·

Perform the inspection while the vehicle is empty (without a spare tire or tools on board).

·

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.




e.

Remove the camber-caster-steering axis inclination gauge and attachment.


f.

Install the wheel cap.

If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.



INSPECT TOE-IN


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to the neutral position.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C241642C02
0.833,0.552 1.073,1.146 1.073,1.146 1.396,0.552 true 2.844,0.417 2.615,0.417 2.615,0.417 2.615,1.292 true 0.958,1.146 1.531,1.573 0.573,0.427 10 *a 2.865,0.333 3.354,0.906 0.49,0.573 10 *b
*a Tread Center Mark
*b Dimension B


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C241643C02
0.542,0.99 0.25,1.427 true 2.5,0.75 2.969,1.125 0.469,0.375 10 *a 2.51,1.781 3.073,2.156 0.563,0.375 10 *b 0.188,1.448 0.729,1.875 0.542,0.427 10 *a
*a Dimension A
*b Dimension B
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front side of the wheels (Dimension A).

Toe-in (Unloaded Vehicle)
Tire Size Engine Specified Condition
185/70 R14 K3-VE B-A: 0 +/- 2.0 mm
(0 +/- 0.0787 in.)
185/65 R15 3SZ-VE B-A: 0 +/- 2.0 mm
(0 +/- 0.0787 in.)

If the toe-in is not within the specified value, adjust it at the rack ends.