Home › Vehicle Exterior › BODY WELD POINT › CENTER BODY PILLAR
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295237 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K102425

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

K137045E01
2.969,5.552 3.667,5.99 0.698,0.438 10 false 160 (6.30) 4.833,5.656 5.531,6.094 0.698,0.438 10 false 45 (1.77) 5.375,5.365 6.073,5.802 0.698,0.438 10 false 385 (15.16) 3.167,6.313 4.208,6.531 1.042,0.219 10 false 40 (1.57) 5.802,6.313 6.844,6.531 1.042,0.219 10 false 25 (0.98) 0.281,8.448 0.802,8.865 0.521,0.417 10 false mm (in.)


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the rocker reinforcement outer, center body pillar reinforcement sub-assembly, center body pillar inner, rocker panel reinforcement and rocker panel reinforcement No.3 with the standard number of welding points.

5.

After welding the rocker reinforcement outer, center body pillar reinforcement sub-assembly, center body pillar inner, rocker panel reinforcement and rocker panel reinforcement No.3 to the vehicle side, install the center body pillar outer.

6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K137046E01
3.667,3.333 3.5,3.333 3.5,3.333 3.875,2.323 false 3.5,8.25 3.25,8.25 3.25,8.25 3.5,7.917 false 2.75,1.417 4.125,1.615 1.375,0.198 10 false 25 (0.98) 4.313,1.427 5.688,1.625 1.375,0.198 10 false 75 (2.95) 3.75,3.24 6.115,3.802 2.365,0.563 10 false ROCKER REINFORCEMENT OUTER 2.708,5.542 3.417,6.083 0.708,0.542 10 false 25 (0.98) 3.583,8.135 6.333,8.865 2.75,0.729 10 false CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY 0.25,8.417 0.917,8.865 0.667,0.448 10 false mm (in.)

K137047E01
3.844,6.083 3.677,6.083 3.677,6.083 5.115,5.146 false 0.75,8.417 0.583,8.417 0.583,8.417 1.958,7.583 false 1.938,2.177 2.25,1.833 2.25,1.833 2.417,1.833 false 1.667,0.698 2,0.333 2,0.333 2.167,0.333 false 2.25,0.24 4.26,0.771 2.01,0.531 10 false CENTER BODY PILLAR INNER 2.51,1.729 4.896,2.26 2.385,0.531 10 false ROCKER PANEL REINFORCEMENT 0.469,4.021 1.938,4.26 1.469,0.24 12 false for RHD: 0.479,6.385 1.948,6.625 1.469,0.24 12 false for LHD: 0.583,4.26 1.135,4.5 0.552,0.24 12 false LH: 3.833,4.25 4.385,4.49 0.552,0.24 12 false RH: 0.583,6.667 1.135,6.906 0.552,0.24 12 false LH: 3.833,6.667 4.385,6.906 0.552,0.24 12 false RH: 3.969,6.01 6.677,6.417 2.708,0.406 10 false ROCKER PANEL REINFORCEMENT NO.3 0.875,8.333 3.583,8.74 2.708,0.406 10 false ROCKER PANEL REINFORCEMENT NO.3

K137048E01
4.583,5.917 4.75,5.917 4.75,5.917 4.938,5.75 false 2.49,5.813 4.563,6.302 2.073,0.49 10 false CENTER BODY PILLAR OUTER