Home › Vehicle Exterior › BODY WELD POINT › ROCKER OUTER PANEL
BM19Y0E _01 Vehicle Exterior _060208 BODY WELD POINT _0295210 ROCKER OUTER PANEL F

BODY WELD POINT  ROCKER OUTER PANEL  ASSEMBLY REPLACEMENT  


K102429

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

*1 in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



K137055E01
5.917,3.083 5.833,3.083 5.833,3.083 5.885,2.844 false 0.344,2.208 1.813,2.448 1.469,0.24 12 false for RHD: 0.344,4.167 1.813,4.406 1.469,0.24 12 false for LHD: 0.417,2.51 0.969,2.75 0.552,0.24 12 false LH: 0.417,4.417 0.969,4.656 0.552,0.24 12 false LH: 2.833,2.51 3.385,2.75 0.552,0.24 12 false RH: 2.833,4.417 3.385,4.656 0.552,0.24 12 false RH: 5.958,2.969 6.271,3.167 0.313,0.198 10 false *1

K137056


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *1 in the illustration.

HINT:

Apply enough adhesive for the panels to stick to each other.


6.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K137057E01
2.458,1.146 2.917,0.135 2.917,0.135 3.083,0.135 false 5.167,1.833 5.083,1.833 5.083,1.833 5.156,1.615 false 3.167,0.031 5.917,0.229 2.75,0.198 10 false ROCKER PANEL OUTER 5.229,1.729 5.542,1.927 0.313,0.198 10 false *1 6.063,2.719 6.635,3.063 0.573,0.344 10 false 5 (0.20) 1.354,4.823 2.823,5.063 1.469,0.24 12 false for RHD: 1.354,6.792 2.823,7.031 1.469,0.24 12 false for LHD: 1.417,5.083 1.969,5.323 0.552,0.24 12 false LH: 1.417,7.083 1.969,7.323 0.552,0.24 12 false LH: 3.833,5.083 4.385,5.323 0.552,0.24 12 false RH: 3.833,7.094 4.385,7.333 0.552,0.24 12 false RH: 0.25,8.417 0.823,8.865 0.573,0.448 10 false mm (in.)

K137058