Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING OR REPLACING PARTS › from 2015.08
BM19Y0E _V1 General _060205 INTRODUCTION _0295247 WHEN REMOVING,INSTALLING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


MEASURE VEHICLE HEIGHT


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C332238N01
1.26,2.104 1.417,2.333 0.156,0.229 10 false A 0.198,2.115 0.354,2.344 0.156,0.229 10 false B 2.01,2.104 2.167,2.333 0.156,0.229 10 false D 3.125,2.073 3.281,2.302 0.156,0.229 10 false C 1.458,3.271 1.615,3.5 0.156,0.229 10 false D 3.063,3.25 3.219,3.479 0.156,0.229 10 false C 1.719,0.615 1.875,0.844 0.156,0.229 10 false A 0.323,0.667 0.479,0.896 0.156,0.229 10 false B

Measure the vehicle height.

Wheel Turning Angle (Unloaded Vehicle):
Tire Size Front A-B Rear C-D
185/70 R14 45.5 mm
(1.79 in.)
57.1 mm
(2.25 in.)
185/65 R15 45.5 mm
(1.79 in.)
56.9 mm
(2.24 in.)


Measuring points:
A:

Ground clearance of front wheel center

B:

Ground clearance of front lower suspension arm set front bolt center

C:

Ground clearance of rear wheel center

D:

Ground clearance of lower control arm set bolt center


NOTICE:
·

Before inspecting the wheel alignment, check the vehicle height.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.





INSPECT WHEEL ANGLE


a.
C132439C01
0.563,0.146 1.021,0.531 0.458,0.385 10 *a 2.781,0.167 3.198,0.604 0.417,0.438 10 *a 2.427,0.167 2.885,0.594 0.458,0.427 10 *b 0.896,0.146 1.354,0.594 0.458,0.448 10 *b
*a Inside
*b Outside
V100135

Front of the Vehicle


Fully turn the steering wheel left and right, and measure the wheel turning angle.

Wheel Turning Angle (Unloaded Vehicle)
Tire Size Inside Wheel Outside Wheel
185/70 R14 43°30' +/- 2°
(43.50° +/- 2°)
37°36' +/- 2°
(37.60° +/- 2°)
185/65 R15 43°30' +/- 2°
(43.50° +/- 2°)
37°36' +/- 2°
(37.60° +/- 2°)

If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.



INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


C132440C03
2.406,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.906,0.708 1.031,0.708 1.031,0.708 1.031,1.479 false 0.708,0.615 1.271,1.031 0.563,0.417 10 *1 2.781,0.729 3.333,1.208 0.552,0.479 10 *2
*1 Alignment tester
*2 Camber-Caster-Steering Axis Inclination Gauge


a.

Put the front wheel on the center of the alignment tester.


b.

Remove the wheel cap.


c.

Set the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.


d.

Inspect the camber, caster and steering axis inclination.

Camber Inclination (Unloaded Vehicle)
Tire Size Camber
185/70 R14 0°30' +/- 45'
(0.5° +/- 0.75°)
185/65 R15 0°30' +/- 45'
(0.5° +/- 0.75°)

Caster Inclination (Unloaded Vehicle)
Tire Size Caster
185/70 R14 5°05' +/- 1°
(5.08° +/- 1°)
185/65 R15 5°05' +/- 1°
(5.08° +/- 1°)

Steering Axis Inclination (Unloaded Vehicle)
Tire Size Steering Axis Inclination
(Reference)
185/70 R14 12°45' +/- 1°
(12.75°)
185/65 R15 12°45' +/- 1°
(12.75°)

NOTICE:
·

Perform the inspection while the vehicle is empty (with a spare tire and tools on board).

·

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.




e.

Remove the camber-caster-steering axis inclination gauge and attachment.


f.

Install the wheel cap.

If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.



INSPECT TOE-IN


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to the neutral position.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C241642C01
0.833,0.552 1.073,1.146 1.073,1.146 1.396,0.552 true 2.844,0.417 2.615,0.417 2.615,0.417 2.615,1.292 true 0.958,1.146 1.531,1.573 0.573,0.427 10 *a 2.865,0.333 3.354,0.906 0.49,0.573 10 *b
*a Tread Center Mark
*b Dimension B


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front side of the wheels (Dimension A).

Toe-in (Unloaded Vehicle)
Tire Size Specified Condition
185/70 R14 B-A: 0 +/- 2.0 mm
(0 +/- 0.0787 in.)
C + D: 0° +/- 0°11'
(0° +/- 0.18°)
185/65 R15 B-A: 0 +/- 2.0 mm
(0 +/- 0.0787 in.)
C + D: 0° +/- 0°11'
(0° +/- 0.18°)

HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified value, adjust it at the rack ends.