Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
NM19Y0E _51 Engine / Hybrid System _003173 K3-VE ENGINE CONTROL _0015998 SFI SYSTEM DE DETAILS F

K3-VE ENGINE CONTROL  SFI SYSTEM  DETAILS  VVT-i CONTROL  


OPERATION


a.

Using the engine speed, vehicle speed, intake air mass, throttle position and water temperature, the ECM can calculate optimal valve timing for each driving condition (target valve timing). The ECM uses this calculated timing to control the camshaft timing oil control valves. In addition, the ECM uses signals from the camshaft position sensor and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W103590E03
0.302,0.646 1.958,1.271 1.656,0.625 10 CRANKSHAFT POSITION SENSOR 0.375,1.458 1.938,2.052 1.563,0.594 10 MANIFOLD ABSOLUTE PRESSURE SENSOR 0.365,2.26 1.813,2.875 1.448,0.615 10 THROTTLE POSITION SENSOR 0.271,3.083 2,3.708 1.729,0.625 10 ENGINE COOLANT TEMPERATURE SENSOR 0.385,3.865 1.885,4.458 1.5,0.594 10 CAMSHAFT POSITION SENSOR 0.427,4.656 1.979,4.938 1.552,0.281 10 Vehicle Speed Signal 3.365,0.906 4.906,1.427 1.542,0.521 10 Target Valve Timing 3.771,3.313 4.719,3.792 0.948,0.479 10 Correction 3.479,3.99 4.938,4.5 1.458,0.51 10 Actual Valve Timing 4.344,2.135 5.229,2.698 0.885,0.563 10 Feedback 5.052,1.135 5.75,1.938 0.698,0.802 10 Duty-cycle Control 5.865,1 7.073,1.854 1.208,0.854 10 CAMSHAFT TIMING OIL CONTROL VALVE 3.865,4.531 4.406,5.052 0.542,0.521 10 ECM


b.

When the camshaft timing oil control valve is operated as illustrated below by the advance signal from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

W103591E03
0.5,2.563 0.708,3.177 0.708,3.177 0.885,3.177 true 0.177,1.813 0.385,1 0.385,1 0.563,1 true 0.635,0.917 1.333,1.458 0.698,0.542 10 Vane 0.958,3.094 2.354,3.646 1.396,0.552 10 Rotation Direction 4.469,2.76 5.302,3.073 0.833,0.313 10 Oil Pressure 6.813,1.292 7.156,1.729 0.344,0.438 10 ECM 5.51,3.073 6.031,3.5 0.521,0.427 10 Drain 5.292,3.073 5.667,3.5 0.375,0.427 10 IN


c.

When the camshaft timing oil control valve is operated as illustrated below by the retard signal from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

W103592E02
0.833,2.49 1.042,3.104 1.042,3.104 1.219,3.104 true 0.51,1.573 0.719,0.5 0.719,0.5 0.896,0.5 true 1.302,3.01 1.885,3.51 0.583,0.5 10 Vane 0.958,0.417 2.292,0.948 1.333,0.531 10 Rotation Direction 4.219,2.802 5.052,3.115 0.833,0.313 10 Oil Pressure 6.792,1.344 7.135,1.656 0.344,0.313 10 ECM 4.906,3.073 5.385,3.521 0.479,0.448 10 Drain 5.333,3.083 5.792,3.542 0.458,0.458 10 IN


d.

After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve assembly in the neutral position unless the traveling state changes. This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.