FUNCTION OF MAIN COMPONENTS
The main components of the 3SZ-VE engine control system are as follows.
| Components | Outline | Quantity | Function |
|---|---|---|---|
| ECM | 32-bit CPU | 1 | The ECM optimally controls the SFI, ESA, and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors. |
| Crankshaft Position Sensor (Rotor Teeth) | Pickup Coil Type (36 - 2 - 1) | 1 | This sensor detects the engine speed and performs cylinder identification. |
| Camshaft Position Sensor (Rotor Teeth) | Pickup Coil Type (3) | 1 | This sensor performs cylinder identification. |
| Knock Sensor | Built-in Piezoelectric Element Type (Flat Type) | 1 | This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking. |
| Intake Air Temperature Sensor | Thermistor Type | 1 | This sensor detects the intake air temperature by means of an internal thermistor. |
| Throttle Position Sensor | Linear Type | 1 | This sensor detects the throttle valve opening angle. |
| Heated Oxygen Sensor (Bank 1, Sensor 1) | Cup Type with Heater | 1 | This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself. |
| Heated Oxygen Sensor (Bank 1, Sensor 2)* | Cup Type with Heater | 1 | |
| Fuel Injector Assembly | 4-hole Type | 4 | The injector is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM. |
| Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the water temperature by means of an internal thermistor. |
| Manifold Absolute Pressure Sensor | Semiconductor (Silicon Chip) Type | 1 | This sensor detects the intake manifold pressure. The ECM calculates the intake air volume based on this signal. |
| Idle Speed Control Valve | Stepper Motor Type (1-coil Type) | 1 | The idle speed control valve is operated by signals from the ECM, and controls the amount of intake air that is allowed to bypass the throttle valve. |
*: Models for Thailand and Mexico
SYSTEM CONTROL
The engine control system of the 3SZ-VE engine has the following systems.
| Components | Function |
|---|---|
| Sequential multiport Fuel Injection (SFI) | D-type SFI system detects the intake manifold pressure with pressure sensor. The fuel injection system is a sequential multiport fuel injection system. |
| Electronic Spark Advance (ESA) | The ECM determines the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signal to the igniter. The ECM corrects ignition timing in response to engine knocking. |
| Variable Valve Timing-intelligent (VVT-i) | Regulates operation of the intake camshaft to ensure optimal valve timing in accordance with engine operating conditions. |
| Idle Speed Control (ISC) | A stepper motor type idle speed control valve controls the fast idle and idle speeds. |
| Fuel Pump Control | Fuel pump operation is controlled by signals from the ECM. |
| Cooling Fan Control | Cooling fan operation is controlled by signals from the ECM based on the engine coolant temperature sensor signal. |
| Heated Oxygen Sensor Heater Control | Maintains the temperature of the oxygen sensor at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration. |
| Air Conditioning Cut-off Control | By turning the air conditioning compressor on or off in accordance with engine operating conditions, drivability is maintained. |
FAIL-SAFE
When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. For details, refer to the Repair Manual for this model.
DIAGNOSIS
When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section. For details, refer to the Repair Manual for this model.