Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
NM19Y0E _51 Engine / Hybrid System _003174 3SZ-VE ENGINE CONTROL _0015999 SFI SYSTEM CO CONTROL F

3SZ-VE ENGINE CONTROL  SFI SYSTEM  CONTROL  VVT-i CONTROL  


FUNCTION


a.

The VVT-i system is designed to control the intake camshafts within a range of 42° (of crankshaft angle) to provide valve timing that is optimally suited to engine operating conditions. This improves torque in all speed ranges as well as increasing fuel economy and reducing exhaust emissions.

W103570E02
1.708,0.521 5.573,1.042 3.865,0.521 10 CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 3.063,1.333 5.448,1.823 2.385,0.49 10 CAMSHAFT POSITION SENSOR 3.125,1.781 4.823,2.563 1.698,0.781 10 ENGINE COOLANT TEMPERATURE SENSOR 3.135,4.042 4.458,4.74 1.323,0.698 10 CRANKSHAFT POSITION SENSOR 5.625,0.99 7.073,1.729 1.448,0.74 10 THROTTLE POSITION SENSOR 5.542,3.177 7.125,4.052 1.583,0.875 10 MANIFOLD ABSOLUTE PRESSURE SENSOR 5.177,2.688 5.76,3.094 0.583,0.406 10 ECM

W103571E03
3.531,3.146 3.302,3.469 3.302,3.469 3.125,3.469 false 4.01,1.354 3.781,0.781 3.781,0.781 3.615,0.781 false 1.073,3.938 2.906,4.469 1.833,0.531 10 : IN Valve Opening Angle 1.083,4.281 2.927,4.802 1.844,0.521 10 : EX Valve Opening Angle 2.115,0.698 3.75,1.229 1.635,0.531 10 VVT-i Operation Range 1.635,3.375 3.323,3.917 1.688,0.542 10 VVT-i Operation Range 4.063,0.5 4.573,0.833 0.51,0.333 10 TDC 4.031,3.792 4.458,4.208 0.427,0.417 10 BDC 3.646,1.177 4.104,1.604 0.458,0.427 10 32° 4.208,0.969 4.604,1.354 0.396,0.385 10 2° 4.354,1.156 4.865,1.594 0.51,0.438 10 10° 4.781,3.552 5.281,3.906 0.5,0.354 10 30° 3.656,3.531 4.135,3.896 0.479,0.365 10 18° 2.948,2.948 3.438,3.26 0.49,0.313 10 60° 4.125,0.698 4.604,1.052 0.479,0.354 10 0°


b.

The VVT-i system delivers excellent benefit vehicle states as shown in the table below.

i.

During Idle

W109497E01
4,0.302 5.271,0.75 1.271,0.448 10 Most Rotarded 3.427,0.094 4.104,0.5 0.677,0.406 10 TDC 2.677,0.813 3.229,1.229 0.552,0.417 10 EX 4.292,0.802 4.844,1.219 0.552,0.417 10 IN 3.417,1.542 4.021,1.781 0.604,0.24 10 BDC

Objective Effect
Decreasing overlap to reduce blow back to the intake side.
·

Stabilized idle speed

·

Better fuel economy




ii.

At Light and Medium Load

W109498E01
2.24,0.073 3.698,0.615 1.458,0.542 10 To Advanced Side 2.729,0.833 3.271,1.333 0.542,0.5 10 EX 4.302,0.823 4.844,1.323 0.542,0.5 10 IN

Objective Effect
Increasing overlap to increase internal EGR to reduce pumping loss
·

Better fuel economy

·

Improved emission control




iii.

In Low to Medium Speed Range with Heavy Load

W109499E01
3.813,1.479 5.844,1.781 2.031,0.302 10 To Advanced Side 4.281,0.875 4.802,1.302 0.521,0.427 10 IN 2.667,0.875 3.188,1.302 0.521,0.427 10 EX

Objective Effect
Advancing the intake valve close timing for volumetric efficiency improvement. Improved torque in low to medium speed range


iv.

In High Speed Range with Heavy Load

W109500E01
2.229,1.49 3.823,1.771 1.594,0.281 10 To Retarded Side 2.677,0.844 3.167,1.177 0.49,0.333 10 EX 4.365,0.854 4.854,1.188 0.49,0.333 10 IN

Objective Effect
Retarding the intake valve close timing for volumetric efficiency improvement Improved output


v.

At Low Temperatures

W109501E01
2.604,0.823 3.083,1.188 0.479,0.365 10 EX 4.365,0.844 4.844,1.208 0.479,0.365 10 IN

Objective Effect
Eliminating overlap to reduce blow back to the intake side stabilizes the idle speed during fast idle.
·

Stabilized idle rpm

·

Better fuel economy




vi.

Upon Starting the Engine

Upon Stopping the Engine

W109502E01
3.958,0.156 5.458,0.656 1.5,0.5 10 Most Retarded 2.615,0.844 3.115,1.302 0.5,0.458 10 EX 4.375,0.844 4.875,1.302 0.5,0.458 10 IN

Objective Effect
Eliminating overlap to minimize blow back to the intake side. Improved startability