Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM
NM19Y0E _57 Power Source / Network _003207 NETWORKING _0016035 MULTIPLEX COMMUNICATION SYSTEM GE GENERAL F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The multiplex communication system uses the following communication protocol:

i.

The Controller Area Network (CAN) is used for communication between the engine, chassis, and body electrical system.



b.

HS-CAN (high speed) is used for the CAN.



MAIN FEATURES


a.

Multiplex communication uses serial communication data that consists of bits and frames in order to exchange information between the various ECUs. This allows a reduction of the amount of wiring used in the vehicle.

i.

A bit is the basic unit of communication used to represent the information. A bit is represented by binary values of "0" or "1".


ii.

A frame is a body of data transmitted together. A frame contains a header that indicates the beginning, and an end message that indicates the end.

Y110277E03
0.073,0.094 2.01,0.698 1.938,0.604 10 Conceptual Drawing 3.865,0.823 4.615,1.313 0.75,0.49 10 Data 3.854,1.958 4.656,2.406 0.802,0.448 10 Frame 0.75,3.448 1.573,3.99 0.823,0.542 10 Battery 2.104,4.281 3.083,4.813 0.979,0.531 10 Switch 2.125,1.104 2.635,1.521 0.51,0.417 10 0 3.302,2.854 3.885,3.219 0.583,0.365 10 On 3.302,3.271 3.833,3.677 0.531,0.406 10 Off 2.781,3.365 3.521,3.896 0.74,0.531 10 ECU 4.823,3.354 5.51,3.844 0.688,0.49 10 ECU 2.094,0.688 2.417,0.948 0.323,0.26 10 1 5.25,1.427 6.396,2.01 1.146,0.583 10 End Message 2.635,1.396 3.635,1.875 1,0.479 10 Header 6.344,3.969 7.156,4.333 0.813,0.365 10 Solenoid 6.479,3.625 7.156,3.99 0.677,0.365 10 Heater 6.479,3.229 7.156,3.594 0.677,0.365 10 Motor 6.479,2.802 7.156,3.167 0.677,0.365 10 Light 0.094,0.865 2.26,1.385 2.167,0.521 10 Serial Communication Data



b.

Differences between Types of CAN

i.

The CAN protocol is the rule for establishing data communication. If the ECUs in the network use different frameworks for their data, such as communication speed, communication wire, and signals, they will be unable to understand each other. Therefore, a protocol (rule) must be established among them.


ii.

The CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately in the engine, chassis, and body electrical system, which requires large amounts of data to be transmitted in short periods of time.



c.

Communication Wire

i.

A twisted pair of wires is used for CAN communication.

Protocol CAN (ISO Standard)

*: bps is an abbreviation of "Bits Per Second", indicating the number of bits that can be transmitted per second.

Communication Speed 500 kbps*/HS-CAN (High Speed)
(Max. 1 Mbps*)
Communication Wire Twisted-pair Wire
Drive Type Differential Voltage Drive
Data Length 1-8 Bytes (Variable)

Communication Wire Outline
Twisted-pair Wire
Y122114

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.

Y110278E03
2.906,1.427 4.385,1.927 1.479,0.5 10 Twisted-pair Wire 2.74,2.063 4.792,2.646 2.052,0.583 10 Differential Voltage Drive 2.271,1.208 2.927,1.719 0.656,0.51 10 ECU 4.354,1.208 5.146,1.708 0.792,0.5 10 ECU