Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE
NM19Y0E _59 Vehicle Exterior _003218 EXTERIOR PANELS / TRIM _0016048 BODY STRUCTURE DE DETAILS F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  DETAILS  RUST-RESISTANT BODY  


CONSTRUCTION


a.

Anti-corrosion Sheet Steel

i.

Anti-corrosion sheet steel is used as in the following illustration:

Y113994
6.938,7.75 7.042,7.75 false
V100145

Anti-corrosion Sheet Steel
V100144

Anti-corrosion Sheet Steel (Models for Thailand, SouthAfrica, Mexico and General only)




b.

Anti-chipping Application and Rust-resistant Performance

i.

Wax is applied to the edges of the hood hinge, spring support, hood lock striker, door hinge, fuel filler lid hinge, the hemmed portions of the hood panel and doors to improve rust-resistant performance.

Y112332
3.688,1.125 4.26,1.531 0.573,0.406 10 *a 6.188,4.031 6.646,4.51 0.458,0.479 10 *e 6.031,2.25 6.531,2.677 0.5,0.427 10 *f 0.938,5.417 1.375,5.813 0.438,0.396 10 *c 4.729,5.448 5.281,5.792 0.552,0.344 10 *d 0.198,0.156 0.698,0.604 0.5,0.448 10 *A 0.865,2.365 1.375,2.885 0.51,0.521 10 *b
*A Front Area - -
*a Cowl Area *b Hood Hinge Area
*c Hood Lock Striker Area *d Spring Support Area
*e Door Hinge Area *f Door Hinge Area (Upper and Lower)
V100145

Injection Wax
V100144

Rust Preventive Wax


Y117378
1.156,1.281 1.615,1.646 0.458,0.365 10 *a 1.01,4.938 1.448,5.365 0.438,0.427 10 *b 5.698,5.458 6.125,5.823 0.427,0.365 10 *c 5.542,1.406 5.948,1.792 0.406,0.385 10 *d
*A Rear Area - -
*a Door Hinge Area (Upper) *b Door Hinge Area (Lower)
*c Fuel Lid Area *d Back Door Hinge Area
V100145

Injection Wax
V100144

Rust Preventive Wax



ii.

In order to prevent scratches to the body caused by chipping while driving, Polyvinyl Chloride (PVC) is provided on the rocker panels.*

HINT:

*: Models without rocker panel moulding


Y112325
6.333,1.51 6.51,1.25 6.51,1.25 6.542,1.25 true 6,2.167 5.854,1.948 5.854,1.948 5.813,1.948 true 5.313,1.448 5.104,1.302 5.104,1.302 5.083,1.302 true 6.125,2.573 6.354,2.74 6.354,2.74 6.479,2.74 true 4.813,0.75 5.333,1.26 0.521,0.51 10 *a 1.927,2.229 2.406,2.688 0.479,0.458 10 A 1.927,2.781 2.531,3.396 0.604,0.615 10 A 6.563,1.167 6.948,1.583 0.385,0.417 10 *3 4.927,1.229 5.448,1.656 0.521,0.427 10 *1 5.646,1.875 6.167,2.365 0.521,0.49 10 *2 6.542,2.688 7.031,3.104 0.49,0.417 10 *b
*1 Floor Side Member Inner *2 Rocker Reinforcement Outer
*3 Side Panel Outer - -
*a A - A Cross Section *b PVC Coating Area
V100145

PVC - -




c.

Under coating is applied to the under side of the body, inside the wheel housing and other parts that are susceptible to stone chipping damage, thus improving the rust-resistant performance of these areas.

Y112315
6.865,5.708 7.021,5.708 false
V100145

Under Coating Area
Y124451

Edge Seal