Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BODY STRUCTURE › 2013.04–2015.08
NM19Y0E _59 Vehicle Exterior _003218 EXTERIOR PANELS / TRIM _0016048 BODY STRUCTURE GE GENERAL F

EXTERIOR PANELS / TRIM  BODY STRUCTURE  GENERAL  GENERAL  


OUTLINE


a.

Highly Rigid Body and Light Weight

i.

High-tensile strength steel is used in order to achieve excellent body rigidity and a lightweight body.



b.

Safety Features

i.

The impact absorbing structure minimizes cabin deformation by effectively helping to absorb the impact energy in the event of a front, side or rear collision. This provides high safety performance.


ii.

A "brake pedal anti-back system" that pushes the brake pedal downwards in the event of a frontal collision, thus reducing the amount of brake pedal retreat has been used in order to mitigate impact to the driver's lower extremities.*


iii.

Knee bolsters (No. 1 instrument panel safety pad and No. 2 instrument panel safety pad) have been added to the driver's side of the instrument panel, reducing injury to the chest and lower extremities.*

*: RHD Models




c.

Rust-resistant Body

i.

Rust-resistant performance is enhanced by the extensive use of anti-corrosion sheet steel, as well as by an anti-corrosion treatment that includes the application of anti-rust wax, sealer and anti-chipping paint to easily corroded parts such as the edge of the door lower portion, door hinge, the fuel filler lid hinge, the hemmed portions of the hood panel and each part of the deck.



d.

Low Vibration and Low Noise Body

i.

Effective application of vibration damping and noise suppressant materials reduces engine, wind and road noise.



e.

Aerodynamics

i.

Optimization of the shape of the body and underfloor ensures excellent aerodynamic performance.




MAIN FEATURES


a.

Exterior Design

i.

Front View

1.

A relief that extends from the hood bulge to the upper grille has been used in combination with a three-dimensional aspect focused on the ornament to achieve a strong, projecting feel for the entire front of the vehicle.

2.

The wheel flares at left and right blend with the vehicle body, giving it a feeling of stability and making it look as though it has a low center of gravity.

Y112334
4.229,2.865 5.125,3.448 5.125,3.448 5.406,2.906 true 3.208,2.823 1.156,3.469 1.156,3.469 0.552,2.802 true 2.135,1.698 3.302,0.615 3.302,0.615 3.438,0.615 true 5.094,3.479 5.552,3.802 0.458,0.323 10 2. 1.125,3.49 1.51,3.76 0.385,0.271 10 2. 3.479,0.51 3.917,0.906 0.438,0.396 10 1.



ii.

Side View

1.

Ramps to absorb force have been put in place on both ends of the shoulder axes at front and rear, shaped to offer a relaxed, yet strong feel to the cabin.

2.

The wheel flares that enclose the tires have been curved to flow into the lower surfaces of the ramp at both front and rear, and the four corners of the vehicle body have clear outlines to convey an impression of firm stability.

3.

A relief has been used from the front wheel to the rear wheel flare, adding life to the sides of the body and shaped so that it flows into the volume of the rear bumper.

Y112335
3.927,1.188 4.51,0.354 4.51,0.354 4.635,0.354 true 1.229,1.844 0.615,1.406 0.615,1.406 0.479,1.406 true 3.427,2.469 2.979,3.177 2.979,3.177 2.844,3.177 true 6.271,1.677 6.615,1.438 6.615,1.438 6.75,1.438 true 4.729,0.25 5.208,0.698 0.479,0.448 10 1. 0.333,1.344 0.719,1.729 0.385,0.385 10 2. 6.792,1.385 7.135,1.729 0.344,0.344 10 2. 2.708,3.104 3.156,3.49 0.448,0.385 10 3.



iii.

Rear View

1.

The area to the left, right, above, and below the license plate at the center of the back door is slightly flared out, which has been shaped to offer a strong feel to the rear view.

2.

The wheel flares at left and right have been given a dynamic shape to blend with the vehicle body, projecting a sense of stability and a low center of gravity.

Y112336
2.083,2.052 3.438,0.802 3.438,0.802 3.583,0.802 true 3.125,2.656 3.521,3.531 3.521,3.531 3.625,3.542 true 0.885,2.646 0.5,3.49 0.5,3.49 0.427,3.49 true 5.5,2.833 5.281,3.552 5.281,3.552 5.156,3.552 true 6.833,2.854 6.844,3.5 6.844,3.5 6.677,3.5 true 6.531,3.427 6.958,3.781 0.427,0.354 10 2. 5.042,3.479 5.375,3.802 0.333,0.323 10 2. 3.688,3.479 4.125,3.76 0.438,0.281 10 2. 0.292,3.417 0.708,3.802 0.417,0.385 10 2. 3.688,0.729 4.115,1.083 0.427,0.354 10 1.



iv.

Sport grade

1.

By using a dedicated front bumper, rear bumper, and rocker panel moulding to emphasize the vehicle's sporty image, the design is differentiated from the standard-grade model, giving it an identity appropriate to the flagship AVANZA model.

Y113391
0.396,2.958 0.552,2.958 0.552,2.958 1.094,2.375 true 4.49,2.635 4.323,2.635 4.323,2.635 3.927,2.208 true 6.625,5.417 6.49,5.417 6.49,5.417 6.073,4.896 true 0.208,2.896 0.656,3.313 0.448,0.417 10 *1 4.542,2.563 5.01,2.979 0.469,0.417 10 *2 6.677,5.354 7.115,5.771 0.438,0.417 10 *3
*1 Front Bumper *2 Rocker Panel Moulding
*3 Rear Bumper - -