Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
NM19Y0E _51 Engine / Hybrid System _041611 1NR-VE ENGINE CONTROL _0193430 SFI SYSTEM DE DETAILS F

1NR-VE ENGINE CONTROL  SFI SYSTEM  DETAILS  KNOCK CONTROL SENSOR  


CONSTRUCTION


a.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking frequency of the cylinder block sub-assembly. This sensor can only detect vibration in this frequency band.


b.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 5 kHz to 15 kHz). It has the following features.


c.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100530E16
3.406,2.938 3.917,2.51 3.917,2.51 4.042,2.51 true 3.406,1.833 3.917,1.396 3.917,1.396 4.052,1.396 true 0.146,0.115 3.844,0.333 3.698,0.219 12 Characteristic of Knock Control Sensor: 0.906,0.646 4.698,0.844 3.792,0.198 10 : Resonance Characteristic of Conventional Type (Resonant) 0.906,0.979 4.698,1.177 3.792,0.198 10 : Resonance Characteristic of Flat Type (Non-resonant) 1.573,1.375 1.792,1.625 0.219,0.25 10 (V) 1.094,2.292 1.594,2.49 0.5,0.198 10 Voltage 3.083,3.365 3.76,3.531 0.677,0.167 10 Frequency 5.26,3.177 5.573,3.427 0.313,0.25 10 (Hz) 4.104,2.448 5.938,2.635 1.833,0.188 10 Detection Band of Flat Type 4.104,1.323 6.438,1.51 2.333,0.188 10 Detection Band of Resonant Type


d.

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.


e.

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.


f.

An open/short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W100954C06
0.281,0.135 3.531,2.51 3.25,2.375 4.708,0.135 6.76,2.479 2.052,2.344 1.083,1.958 0.958,1.24 0.958,1.24 0.865,1.24 true 1.146,1.875 0.958,0.615 0.958,0.615 0.865,0.615 true 1.167,1.75 1.313,0.531 1.313,0.531 1.417,0.531 true 2.313,1.948 2.396,0.76 2.396,0.76 2.51,0.76 true 5.698,1.542 6.115,0.802 6.115,0.802 6.219,0.802 true 5.76,1.573 6.104,1.958 6.104,1.958 6.188,1.958 true 0.677,1.167 0.875,1.354 0.198,0.188 10 *3 0.677,0.542 0.875,0.729 0.198,0.188 10 *2 1.469,0.479 1.667,0.667 0.198,0.188 10 *1 2.563,0.677 2.76,0.865 0.198,0.188 10 *4 0.333,0.156 0.615,0.406 0.281,0.25 10 *A 4.792,0.156 5.063,0.406 0.271,0.25 10 *B 6.229,0.75 6.427,0.938 0.198,0.188 10 *3 6.198,1.885 6.396,2.073 0.198,0.188 10 *5
*A Flat Type Knock Control Sensor
(Non-Resonant Type)
*B Conventional Type Knock Control Sensor
(Resonant Type)
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open Circuit Detection Resistor
*5 Vibration Plate - -


W110719E03
1.906,2.469 1.677,2.469 1.677,2.469 1.396,1.427 true 2.771,2.135 2.521,2.135 2.521,2.135 2.115,1.563 true 0.885,0.51 3.083,0.771 2.198,0.26 10 false Flat Type Knock Control Sensor 2.188,1.323 2.958,1.521 0.771,0.198 10 false 200 kΩ 3.979,1.125 4.594,1.323 0.615,0.198 10 false KNK 3.958,1.771 4.573,1.969 0.615,0.198 10 false E2 5.052,1.333 5.51,1.531 0.458,0.198 10 false ECM 2.823,2.073 5.229,2.333 2.406,0.26 10 false Open/Short Circuit Detection Resistor 1.979,2.396 5.188,2.594 3.208,0.198 10 false Piezoelectric Element


g.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W101072C06
3.573,1.281 2.896,1.146 2.896,1.146 2.802,1.146 true 3.583,0.948 2.917,0.271 2.917,0.271 2.844,0.271 true 2.635,1.063 2.833,1.292 0.198,0.229 10 *2 2.688,0.208 2.885,0.438 0.198,0.229 10 *1
*1 Steel Weight *2 Piezoelectric Element
V100135

Inertia - -