Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
NM19Y0E _52 Drivetrain _041627 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0193439 AUTOMATIC TRANSMISSION SYSTEM CO CONTROL F

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


SYSTEM CONTROL


a.

The electronic control system of the A4R automatic transmission consists of the control function listed below :

Control Function
Direct Hydraulic Pressure Control This control uses shift solenoid valve SL1 and shift solenoid valve SL2 to directly control the control hydraulic pressure to the clutches and brakes (B1, C2, C3), without using the shift valve.
Clutch to Clutch Pressure Control The shift solenoid valve SL1 and shift solenoid valve SL2 minutely controls the clutch pressure in accordance with the engine output and driving conditions.
Line Pressure Control This control uses the line pressure control solenoid assembly (SLT) to control the line pressure in 1st to 4th gears in accordance with the torque at the output shaft.
Engine Torque Control This control retards the engine ignition timing temporarily to improve shift feeling during up or down shifting.
Lock-up Timing Control The ECM sends current to shift solenoid valve DSL (SL) based on signals from each sensor and engages or disengages the lockup clutch.
"N" to "D" Squat Control When the shift lever is moved from N to D, 3, 2, L, the gear is temporarily shifted to 2nd and then to 1st to reduce vehicle squat.
Low Gear Inhibitor Control If a shift-down request is made through the operation of the shift lever while the vehicle is being driven at high speeds, this control maintains the current gear position until the vehicle speed drops below a prescribed speed.
Reverse Inhibitor Control When the driver inadvertently moves the shift lever to the reverse position while the vehicle is running forward at speed above a certain speed, the control works so that the gear can not be put into the reverse position.
Low-temperature Shift Restriction Control Shift restriction is effected if the fluid temperature is low immediately after the vehicle has been started at extremely low temperatures.
·

When the fluid temperature is below -10 °C (14 °F), shifting into 3rd gear is prohibited.

·

When the fluid temperature is below 10 °C (50 °F), shifting into 4th gear is prohibited.


Fail-safe Even if a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's drivability from being affected significantly.


b.

Direct Hydraulic Pressure Control

i.

The shift elements B1, C2 and C3 are directly coupled to the respective control valves. The control valves control the hydraulic pressure of the respective shift control elements in order to shift gears. Furthermore, the shift solenoid valve SL1 and SL2, which generate the signal pressure that acts on the control valves, are connected to the respective control valves.


ii.

By regulating the current that is applied to the linear solenoid valves in order to vary their signal pressure, the ECM varies the signal pressure in order to control the output hydraulic pressure.

X130008E01
1.813,1.719 2.885,1.99 1.073,0.271 10 false Linear Solenoid 5.708,1.833 6.146,2.094 0.438,0.26 10 false ECM 1.719,0.26 3.438,0.583 1.719,0.323 10 false Output Hydraulic Pressure 0.302,0.333 1.26,0.885 0.958,0.552 10 false Shift Control Elements



c.

Clutch to Clutch Pressure Control

i.

During the transient shift stage, this control simultaneously controls the hydraulic pressure of both the disengaged clutch (brake) and the engaged clutch (brake). This prevents the engine from revving during the transient shift stage or the planetary gear from becoming interlocked, thus realizing a smooth and responsive shifting.


ii.

Based on the engine torque information and the transmission fluid temperature provided by the ECM, the ECM effects feedback control on the solenoid valve for the engaged and disengaged clutches (brakes) so that the target rate of change in the input speed is attained. As a result, an efficient torque fluctuation is realized at the output shaft.

X130009E01
0.729,3.198 1.635,3.458 0.906,0.26 10 false Line Pressure 5.542,2.26 6.635,2.646 1.094,0.385 10 false Engaged Clutch 4.031,2.24 5.208,2.615 1.177,0.375 10 false Disengaged Clutch 0.24,1.656 1.833,1.958 1.594,0.302 10 false ATF Temperature Sensor 5.365,0.979 6.313,1.25 0.948,0.271 10 false Linear Solenoid 4.177,0.969 5.156,1.292 0.979,0.323 10 false Linear Solenoid 3.833,0.458 4.281,0.719 0.448,0.26 10 false ECM 0.156,0.979 2.177,1.552 2.021,0.573 10 false Input Speed Sensor (Transmission Revolution Sensor) 0.146,0.188 2.208,0.833 2.063,0.646 10 false Output Speed Sensor (Transmission Revolution Sensor) 0.25,2.021 1.271,2.385 1.021,0.365 10 false Engine Torque 1.969,2.333 2.229,2.594 0.26,0.26 10 false etc. 3.594,1.646 4.75,2.167 1.156,0.521 10 false Output Hydraulic Pressure 5.948,1.625 7.094,2.135 1.146,0.51 10 false Output Hydraulic Pressure




FUNCTION


a.

Shift Lock System

i.

The shift lock mechanism prevents the shift lever from being shifted to any position other than the P, unless the ignition switch is ON, and the brake pedal is depressed. This mechanism helps to prevent unintentional acceleration.


ii.

The key interlock device prevents the key from being pulled out after the ignition switch is turned off, unless the shift lever is moved to the P. Thus, the driver is urged to park the vehicle in the P.


iii.

The shift lock system mainly consists of the shift lock control ECU, shift lock solenoid, key interlock solenoid and shift lock override button.


iv.

The shift lock solenoid assembly has a built-in P detection switch.

X106758E03
0.365,2.125 1.688,2.5 1.323,0.375 10 false Ignition Switch 0.25,0.938 1.583,1.563 1.333,0.625 10 false Stop Light Switch Assembly 2.823,1.49 3.99,2.167 1.167,0.677 10 false Shift Lock Control ECU 5.438,1.115 6.75,1.469 1.313,0.354 10 false Shift Lock Solenoid 5.479,2.052 6.771,2.406 1.292,0.354 10 false P Detection Switch 4.896,2.854 6.802,3.323 1.906,0.469 10 false Shift Lock Solenoid Assembly




FAIL-SAFE


a.

This function minimizes the loss of operation when any abnormality occurs in the input or output signal systems in the ECM.


b.

For details, refer to the corresponding Repair Manual for this model.



DIAGNOSIS


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM illuminates MIL or blinks the D position indicator light in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions.


c.

The DTCs can be read by connecting a GTS to the DLC3.


d.

For details, refer to the corresponding Repair Manual for this model.