Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › ENGINE UNIT › from 2015.08
NM19Y0E _51 Engine / Hybrid System _041614 2NR-VE ENGINE MECHANICAL _0199634 ENGINE UNIT DE DETAILS F

2NR-VE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

An aluminum cylinder block sub-assembly with a 7 mm (0.276 in.) distance between the cylinder bores is used to achieve a compact and lightweight configuration.


b.

A spiny type liner, which has an irregularly shaped outer casting surface, is used to enhance the adhesion between the liners and the aluminum of the cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores. A cylinder block sub-assembly with this type of liner cannot be rebored.

W128825C01
5.115,0.677 5.438,0.677 5.438,0.677 5.844,1.833 true 5.146,3.479 5.438,3.479 5.438,3.479 5.771,2.646 true 1.875,0.542 2.188,0.74 0.313,0.198 10 false *a 4.906,0.604 5.219,0.802 0.313,0.198 10 false *b 4.948,3.406 5.26,3.604 0.313,0.198 10 false *1
*1 Spiny Type Liner - -
*a 7 mm (0.276 in.) *b Irregularly Shaped Outer Casting Surface of Liner



c.

The cylinder block sub-assembly has been heat-treated, suppressing deformation of the cylinder bores caused by time-induced deforming of the cylinder block sub-assembly, and reducing engine oil consumption.


d.

Water passages have been provided between each cylinder bore. This construction ensures that the passage of coolant actively cools the top of the cylinder bore, which is easily affected by heat, and keeps the temperature distribution in a circular direction uniform on the bore wall. This uniform temperature distribution improves anti-knock performance and keeps heat deformation between cylinder bores to a minimum, reducing friction and delivering high performance with low fuel consumption. Additionally, this structure lowers the temperature between cylinder bores, preventing leakage from the cylinder head gasket and improving reliability.

W128826C01
4.823,1.646 5.083,0.417 5.083,0.417 5.417,0.417 true 5.167,1.833 6.167,0.771 6.167,0.771 6.5,0.771 true 5.458,0.323 5.771,0.521 0.313,0.198 10 false *a 6.531,0.677 6.844,0.875 0.313,0.198 10 false *a
*a Water Passage - -



e.

Through the use of an offset crankshaft, the centerline of the cylinder bores is shifted 8 mm (0.315 in.) towards the exhaust in relation to the centerline of the crankshaft. Thus, the side force (thrust) applied to the cylinder walls is reduced when maximum combustion pressure is applied. This contributes to fuel economy.

W128698C01
3.667,1.76 3.969,1.76 3.969,1.76 4.51,2.25 true 1.49,0.833 1.802,1.031 0.313,0.198 10 false *a 1.906,0.521 2.219,0.719 0.313,0.198 10 false *b 1.833,3.396 2.146,3.594 0.313,0.198 10 false *c 4.458,0.302 4.771,0.5 0.313,0.198 10 false *f 5.792,0.281 6.104,0.479 0.313,0.198 10 false *f 3.479,1.677 3.792,1.875 0.313,0.198 10 false *c 4.438,3.271 4.75,3.469 0.313,0.198 10 false *d 5.938,3.26 6.25,3.458 0.313,0.198 10 false *e
*a 8 mm (0.315 in) *b Bore Centerline
*c Crankshaft Centerline *d Offset Crankshaft
*e Non-offset Crankshaft *f Maximum Pressure



f.

A cylinder block water jacket spacer is provided in the cylinder block sub-assembly.


g.

The cylinder block water jacket spacer suppresses the water flow in the center of the water jackets, guides the coolant above and below the cylinder bores, and ensures uniform temperature distribution. As a result, the viscosity of the engine oil that acts as a lubricant between the bore walls and the pistons can be lowered, thus reducing friction.

W128699C01
1.917,0.344 2.469,0.344 2.469,0.344 3.094,0.927 true 4.688,1.948 5.292,1.542 5.292,1.542 5.948,1.542 true 1.719,0.281 2.031,0.479 0.313,0.198 10 false *1 5.99,1.469 6.302,1.667 0.313,0.198 10 false *2
*1 Cylinder Block Water Jacket Spacer *2 Cylinder Block Sub-assembly
V100135

Engine Front - -