CONSTRUCTION
The brake actuator assembly consists of an actuator portion and a skid control ECU.
The actuator portion consists of 2 master cylinder cut solenoid valves, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs and a master cylinder pressure sensor.*1
The actuator portion consists of 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, and 2 reservoirs.*2
*1: Models with VSC
*2: Models without VSC
| *A | Models with VSC | *B | Models without VSC |
| *1 | Skid Control ECU
·
Solenoid Relay ·
Motor Relay ·
Motor Cut Relay |
*2 | Actuator Portion
·
Master Cylinder Cut Solenoid Valve ·
Pressure Holding Solenoid Valve ·
Pressure Reduction Solenoid Valve ·
Master Cylinder Pressure Sensor ·
Pump ·
Reservoir |
| *3 | Actuator Portion
·
Pressure Holding Solenoid Valve ·
Pressure Reduction Solenoid Valve ·
Pump ·
Reservoir |
- | - |
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
| *1 | Master Cylinder Pressure Sensor | *2 | No. 1 Master Cylinder Cut Solenoid Valve |
| *3 | No. 2 Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Pressure Reduction Solenoid Valve | *6 | Pump |
| *7 | Reservoir | *8 | Brake Actuator |
| *a | From Brake Master Cylinder Sub-assembly | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Pump | *4 | Reservoir |
| *5 | Brake Actuator | - | - |
| *a | From Master Cylinder | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
OPERATION
ABS and EBD
Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator assembly in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Port A | *4 | Port B |
| *a | Pressure Increase Mode | *b | Pressure Holding Mode |
| *c | Pressure Reduction Mode | *d | To Brake Cylinder |
| *e | From Brake Cylinder | - | - |
| Pressure Mode | Increase Mode | Holding Mode | Reduction Mode |
| Pressure Holding Solenoid Valve (Port A) | Off (Open) | On (Closed) | ← |
| Pressure Reduction Solenoid Valve (Port B) | Off (Closed) | ← | On (Open) |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
Brake Assist
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Master Cylinder Pressure Sensor | *2 | No. 1 Master Cylinder Cut Solenoid Valve |
| *3 | No. 2 Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Pressure Reduction Solenoid Valve | *6 | Pump |
| *7 | Reservoir | *8 | Brake Actuator |
| *a | From Brake Master Cylinder Sub-assembly | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
| Item | Brake Assist Not Activated | Brake Assist Activated | |
|---|---|---|---|
| Pump | Off | On | |
| No. 1 Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* |
| No. 2 Master Cylinder Cut Solenoid Valve | Port (B) | Off (Open) | On* |
| Pressure Holding Solenoid Valve | Port (C) | Off (Open) | ← |
| Port (D) | Off (Open) | ← | |
| Port (E) | Off (Open) | ← | |
| Port (F) | Off (Open) | ← | |
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← |
| Port (H) | Off (Closed) | ← | |
| Port (I) | Off (Closed) | ← | |
| Port (J) | Off (Closed) | ← | |
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
Traction Control (TRC)
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes to control the slippage of the drive wheels. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | No. 1 Master Cylinder Cut Solenoid Valve |
| *3 | No. 2 Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Pressure Reduction Solenoid Valve | *6 | Pump |
| *7 | Reservoir | *8 | Brake Actuator |
| *a | From Brake Master Cylinder Sub-assembly | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
| Item | TRC Operation | |||||
|---|---|---|---|---|---|---|
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| No. 1 Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| No. 2 Master Cylinder Cut Solenoid Valve | Port (B) | Off (Open) | On* | ← | ← | |
| Front Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | On (Closed) | ← | ← |
| Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | ← | |
| Port (J) | Off (Closed) | ← | ← | ← | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (D) | Off (Open) | ← | On (Closed) | ← |
| Port (E) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (H) | Off (Closed) | ← | ← | On (Open) | |
| Port (I) | Off (Closed) | ← | ← | On (Open) | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
Vehicle Stability Control (VSC)
The VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.
In the front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | No. 1 Master Cylinder Cut Solenoid Valve |
| *3 | No. 2 Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Pressure Reduction Solenoid Valve | *6 | Pump |
| *7 | Reservoir | *8 | Brake Actuator |
| *a | From Brake Master Cylinder Sub-assembly | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
| Item | VSC Operation | |||||
|---|---|---|---|---|---|---|
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| No. 1 Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| No. 2 Master Cylinder Cut Solenoid Valve | Port (B) | Off (Open) | On* | ← | ← | |
| Front Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | On (Closed) | ← | ← |
| Port (F) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | ← | On (Open) | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (D) | Off (Open) | ← | On (Closed) | ← |
| Port (E) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (H) | Off (Closed) | ← | ← | On (Open) | |
| Port (I) | Off (Closed) | ← | ← | On (Open) | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.
During the rear wheel skid restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Master Cylinder Pressure Sensor | *2 | No. 1 Master Cylinder Cut Solenoid Valve |
| *3 | No. 2 Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Pressure Reduction Solenoid Valve | *6 | Pump |
| *7 | Reservoir | *8 | Brake Actuator |
| *a | From Brake Master Cylinder Sub-assembly | *b | Front Disc Brake Cylinder RH |
| *c | Rear Wheel Brake Cylinder LH | *d | Rear Wheel Brake Cylinder RH |
| *e | Front Disc Brake Cylinder LH | - | - |
| Item | VSC Operation | |||||
|---|---|---|---|---|---|---|
| Not Activated | Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||
| Pump | Off | On | ← | ← | ||
| No. 1 Master Cylinder Cut Solenoid Valve | Port (A) | Off (Open) | On* | ← | ← | |
| No. 2 Master Cylinder Cut Solenoid Valve | Port (B) | Off (Open) | On* | ← | ← | |
| Front Brake | Pressure Holding Solenoid Valve | Port (C) | Off (Open) | On (Closed) | ← | ← |
| Port (F) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| Port (J) | Off (Closed) | ← | ← | On (Open) | ||
| Rear Brake | Pressure Holding Solenoid Valve | Port (D) | Off (Open) | ← | On (Closed) | ← |
| Port (E) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | Port (H) | Off (Closed) | ← | ← | On (Open) | |
| Port (I) | Off (Closed) | ← | ← | On (Open) | ||
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually.