Home › General › INTRODUCTION › HOW TO USE THIS MANUAL
RM19Y0E _V1 General _002963 INTRODUCTION _0014842 HOW TO USE THIS MANUAL F

INTRODUCTION  HOW TO USE THIS MANUAL  GENERAL INFORMATION  


GENERAL DESCRIPTION


a.

Repair operations can be separated mainly into the following 3 processes:

i.

Diagnosis


ii.

Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting


iii.

Final Inspection



b.

The following procedures are omitted from this manual. However, these procedures must be performed.

i.

Use a jack or lift to perform operations.


ii.

Clean all removed parts.


iii.

Perform a visual check.




INDEX


a.

An alphabetical INDEX section is provided at the end of the manual as a reference to help you find the item to be repaired.



PREPARATION


a.

Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the working procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.



REPAIR PROCEDURES


a.

A component illustration is placed under the title where necessary.


b.

Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.

The following illustration is an example.

D100720
2.938,1.854 3.542,2.031 0.604,0.177 0.313,2.292 1.063,2.469 0.75,0.177 1.531,0.5 1.771,0.5 false 1.063,0.823 0.802,0.823 false 1.479,1.25 1.729,1.25 false 1.198,2.375 1.063,2.375 false 1.125,2.823 0.906,2.823 false 1.781,2.146 2.01,1.573 2.01,1.573 2.104,1.573 false 2.802,1.938 2.938,1.938 false 4.167,2.208 4.167,2.656 false 3.313,2.646 3.313,2.479 false 5,2.073 5,2.458 false 5.313,2.021 5.313,2.177 false 5.906,1.771 5.906,2.104 false 6.333,1.698 6.333,1.833 false 6.635,1.573 6.75,1.573 false 4.708,1.885 4.708,1.604 4.708,1.604 4.583,1.604 false 5.615,1.354 5.615,1.188 5.615,1.188 5.531,1.188 false 0.656,1.635 0.906,1.635 false 5.813,1.323 5.813,1.063 5.813,1.063 5.896,1.063 false 2.958,1.875 3.74,2.125 0.781,0.25 8 12 (120, 9) 0.375,2.302 1.208,2.604 0.833,0.302 8 15 (153, 11) 1.844,0.406 2.156,0.563 0.313,0.156 10 *1 0.594,0.729 0.906,0.885 0.313,0.156 10 *2 1.802,1.156 2.115,1.313 0.313,0.156 10 *3 0.406,1.552 0.719,1.708 0.313,0.156 10 *4 2.188,1.469 2.604,1.667 0.417,0.198 10 ● *5 4.354,1.51 4.698,1.802 0.344,0.292 10 *6 5.167,1.094 5.927,1.594 0.76,0.5 10 ● *7 5.979,0.958 6.406,1.281 0.427,0.323 10 *8 6.802,1.51 7.135,1.771 0.333,0.26 10 *9 6.208,1.865 6.667,2.208 0.458,0.344 10 *10 5.792,2.156 6.333,2.438 0.542,0.281 10 *11 5.208,2.229 5.771,2.531 0.563,0.302 10 *12 4.875,2.51 5.344,2.854 0.469,0.344 10 *13 4.042,2.708 4.5,2.958 0.458,0.25 10 *14 3.198,2.667 3.604,2.938 0.406,0.271 10 *15 0.604,2.74 1.01,2.969 0.406,0.229 10 *16 0.125,0.115 0.438,0.271 0.313,0.156 10 *a
*1 FILTER CAP *2 FLOAT
*3 RESERVOIR TANK *4 SLOTTED SPRING PIN
*5 GROMMET *6 WASHER
*7 GASKET *8 CLEVIS PIN
*9 CLIP *10 CLEVIS
*11 LOCK NUT *12 BOOT
*13 SNAP RING *14 PUSH ROD
*15 PISTON *16 CYLINDER
*a Example - -
V100146

N*m (kgf*cm, ft*lbf) : Specified torque ● Non-reusable part




c.

Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.

HINT:

There are cases where such information can only be explained by using an illustration. In these cases, the information is described in the illustration.



d.

Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.

Illustration What to do and where to do it.
Task heading What work will be performed.
Explanation text How to perform the task.
Also has information such as specifications and warnings, which are written in boldface text.


e.

Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.


f.

Procedures are presented in a step-by-step format.



SERVICE SPECIFICATIONS


a.

SPECIFICATIONS are presented in boldface text throughout the manual. The specifications are also found in the "Specifications" section for reference.



TERM DEFINITIONS


CAUTION Possibility of injury to you or other people.
NOTICE Possibility of damage to components being repaired.
HINT Provides additional information to help you perform repairs.


INTERNATIONAL SYSTEM OF UNITS


a.

The units used in this manual comply with the International System of Units (SI) standard. Units from the metric system and the English systems are also provided.

Below is an example.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)