Home › General › SPECIFICATIONS › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › 2011.11–2015.08
RM19Y0E _V1 General _002965 SPECIFICATIONS _0014942 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE F

SPECIFICATIONS  A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  SERVICE DATA  


Line pressure (Wheel locked)
AT stall (Throttle valve fully opened) D position 930 to 1,120 kPa (9.5 to 11.4 kgf*cm2, 135 to 162 psi)
R position 1,520 to 2,110 kPa (15.5 to 21.5 kgf*cm2, 220 to 306 psi)
Engine stall revolution D and R positions 2,100 to 2,600 rpm
Time lag N → D position Less than 1.0 second
N → R position Less than 1.0 second
Engine idle speed (A/C OFF) N position 750 rpm
Drive plate runout Maximum 0.25 mm (0.0098 in.)
Torque converter clutch runout Maximum 0.30 mm (0.0118 in.)
Extension housing oil seal drive in depth 1.0 to 2.0 mm (0.039 to 0.079 in.)
Shift schedule
D position
(Throttle valve fully opened) 1 → 2 38 to 53 km/h (24 to 33 mph)
2 → 3 78 to 93 km/h (48 to 58 mph)
3 → O/D 130 to 145 km/h (81 to 90 mph)
O/D → 3 122 to 137 km/h (76 to 85 mph)
3 → 2 71 to 86 km/h (44 to 53 mph)
2 → 1 27 to 42 km/h (17 to 26 mph)
(Throttle valve fully closed) 3 → O/D 38 to 53 km/h (24 to 33 mph)
O/D → 3 20 to 35 km/h (12 to 22 mph)
2 position
(Throttle valve fully opened) 1 → 2 38 to 53 km/h (24 to 33 mph)
3 → 2 75 to 90 km/h (47 to 56 mph)
2 → 1 27 to 42 km/h (17 to 26 mph)
L position
(Throttle valve fully opened) 2 → 1 34 to 49 km/h (21 to 30 mph)
Lock-up point (Throttle valve opening 5 to 20 %)
D position
O/D gear Lock-up ON 62 to 77 km/h (39 to 48 mph)
Lock-up OFF 58 to 73 km/h (36 to 45 mph)
3rd gear Lock-up ON 99 to 114 km/h (62 to 71 mph)
Lock-up OFF 88 to 103 km/h (55 to 64 mph)
Automatic transmission extension housing oil seal Drive in depth 1.0 to 2.0 mm (0.039 to 0.079 in.)
Park/neutral position switch assembly resistance Standard
P (4 - 6)
Except P (4 - 6)
R (1 - 7)
Except R (1 - 7)
N (5 - 6)
Except N (5 - 6)
D (3 - 6)
Except D (3 - 6)
2 (2 - 6)
Except 2 (2 - 6)
L (6 - 8)
Except L (6 - 8)
-
Below 1 Ω
10 kΩ or higher
Below 1 Ω
10 kΩ or higher
Below 1 Ω
10 kΩ or higher
Below 1 Ω
10 kΩ or higher
Below 1 Ω
10 kΩ or higher
Below 1 Ω
10 kΩ or higher
Torque converter clutch sleeve runout Maximum 0.30 mm (0.0118 in.)
Drive plate runout Maximum 0.25 mm (0.0098 in.)
Front oil pump body sub-assembly end play Standard 0.26 to 0.88 mm (0.0102 to 0.0346 in.)
1st and reverse brake end play Standard 0.65 to 1.13 mm (0.0256 to 0.0445 in.)
2nd and 4th brake end play Standard 1.07 to 1.52 mm (0.0421 to 0.0598 in.)
Planetary sun gear sub-assembly inside diameter Maximum 27.07 mm (1.0657 in.)
Rear planetary sun gear sub-assembly inside diameter Maximum 18.07 mm (0.7114 in.)
Front planetary ring gear assembly inside diameter Maximum 13.07 mm (0.5146 in.)
1st and reverse brake flange thickness Mark 0
Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
4.0 mm (0.157 in.)
4.2 mm (0.165 in.)
4.4 mm (0.173 in.)
4.6 mm (0.181 in.)
4.8 mm (0.189 in.)
5.0 mm (0.197 in.)
2nd and 4th brake piston snap ring thickness Black
Brown
Blue
Silver
2.25 mm (0.0886 in.)
2.00 mm (0.0787 in.)
1.75 mm (0.0689 in.)
1.50 mm (0.0591 in.)
Rear multiple disc clutch assembly installation height Standard Approximately 43 mm (1.69 in.)
Front multiple disc clutch assembly installation height Standard Approximately 43.5 mm (1.71 in.)
Bearing thickness
(Front oil pump body sub-assembly x Front multiple disc clutch assembly)
3.41 mm (0.1343 in.)
3.81 mm (0.1500 in.)
4.21 mm (0.1657 in.)
Automatic transmission extension housing oil seal Drive in depth 1.0 to 2.0 mm (0.039 to 0.079 in.)
Front oil pump body sub-assembly busing inside diameter Maximum 23.52 mm (0.9260 in.)
Stator shaft busing inside diameter Maximum 18.72 mm (0.7370 in.)
Front multiple disc clutch assembly Forward clutch piston stroke
Reverse clutch piston stroke
0.33 to 1.27 mm (0.0130 to 0.0500 in.)
0.67 to 0.98 mm (0.0264 to 0.0386 in.)
Front multiple disc drum inside diameter Standard
Maximum
44.50 to 44.52 mm (1.7520 to 1.7528 in.)
44.58 mm (1.7551 in.)
Rear multiple disc clutch assembly Rear clutch piston stroke 1.20 to 1.51 mm (0.0472 to 0.0594 in.)

LUBRICANT
Item Capacity Classification
Automatic transmission fluid
(Drain and refill)
1.5 liter (1.6 US qts, 1.3 Imp. qts) Toyota Genuine ATF Type T-IV