Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM C

K3-VE ENGINE CONTROL  SFI SYSTEM  P1604  Startability Malfunction  


DESCRIPTION

When the engine can not start or takes a very long time to start, although the STA signals are input, DTC is output. The freeze-frame data, which have memorized the engine conditions when DTC was output, can be checked using the intelligent tester. The ability to check, by the freeze-frame data, the engine conditions when an engine start malfunction occurs, improves vehicle maintenance services. Moreover, because an engine start malfunction due to a lack of fuel is also detected, the fuel must be checked before operation.

DTC No. Detection Item DTC Detection Condition MIL Memory
P1604 Startability Malfunction Either of following condition met:
(1 trip detection logic)
·

The engine does not start even if the starter ON signal input exceeds 1.5 sec.*1

·

The engine stops as soon as engine speed exceeds 500 rpm after starting.*2


- DTC stored

*1: In case that the engine is difficult to start or that the engine does not start.

*2: In case that the engine speed drops or the engine stalls right after engine start.


CAUTION / NOTICE / HINT

HINT:
·

When other DTCs are displayed, first troubleshoot the corresponding DTC.

·

Because DTC P1604 differs from the conventional DTC, the following procedure is described as an example.



PROCEDURE

1.CHECK OPERATION OF ENGINE CRANKING
a.

Check that the engine cranks.

Result:
Result Proceed to
Cranking A
Not cranking B




A

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1604)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1604)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 206

d.

Read DTCs.

Result:
Result Proceed to
P1604 A
P1604 and other DTCs B




A

3.CHECK FREEZE DATA

B

3.CHECK FREEZE DATA
HINT:

Using the time series freeze-frame data, check the data when and after the DTC is detected, to be used for troubleshooting.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check the time series freeze-frame data following the instructions displayed on the intelligent tester, and check the vehicle conditions when an engine start malfunctions.

Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA


d.

Check the freeze-frame data of the battery state.

Tester Display
Battery Voltage -


e.

Check the freeze-frame data of the cranking state.

Tester Display
Engine Speed -


f.

Compare the freeze-frame data for each temperature when an engine start malfunctions.

Tester Display
Coolant Temp Intake Air


g.

Check the freeze-frame data of engine control when the engine starts.

Tester Display
MAP -


h.

Check the freeze-frame data of the fuel injection.

Tester Display
Injection Volume Injection Time


i.

Referring to the above freeze-frame data, perform the reproduction test.


j.

Based on the freeze-frame data and the reproduction test, specify the malfunctioning section while comparing to the reference values shown in the ECM data list description.

Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

Result:
Result Proceed to
The malfunctioning section can be specified. A
The malfunctioning section can not be specified. B




A

CHECK AND REPAIR LOCATION WHERE MALFUNCTION EXIST

B