Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2014.04
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) U

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  TERMINALS OF ECM  


CHECK ECM


A141508N01
3.333,0.615 3.677,0.823 0.344,0.208 5.156,0.615 5.5,0.823 0.344,0.208 1.74,0.615 2.083,0.823 0.344,0.208 3.385,0.635 3.979,1.073 0.594,0.438 10 C24 1.792,0.635 2.438,1.031 0.646,0.396 10 C23 5.25,0.635 5.771,1.042 0.521,0.406 10 E3

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C23-1 (#40) - C24-7 (E01) V - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
C23-2 (#30) - C24-7 (E01) R - W-B
C23-3 (#20) - C24-7 (E01) P - W-B Idling Pulse generation
(See waveform 1)
C23-4 (#10) - C24-7 (E01) W-R - W-B
C23-6 (OCV+) - C23-5 (OCV-) G - LG Camshaft timing oil control valve assembly Idling Pulse generation
(See waveform 2)
C23-7 (+B1) - C24-32 (E1) L - W-B Power source of ECM Ignition switch ON 11 to 14 V
C23-9 (IG4) - C24-32 (E1) L - W-B Ignition coil assembly
(Ignition signal)
Ignition switch ON Below 0.5 V
C23-10 (IG3) - C24-32 (E1) G - W-B
C23-11 (IG2) - C24-32 (E1) R - W-B Idling Pulse generation
(See page )
C23-12 (IG1) - C24-32 (E1) B - W-B
C23-15 (IAHI) - C23-14 (IALO) V - G-W Idle speed control valve Idling, air conditioning OFF or ON Pulse generation
(0 to 12 V)
C23-17 (IBHI) - C23-16 (IBLO) LG - P
C23-24 (PRG) - C24-7 (E01) W - W-B Purge VSV Ignition switch ON 11 to 14 V
Idling, under purge operation Pulse generation
(See waveform 3)
C23-34 (ALT) - C24-32 (E1) B-W - W-B Generator assembly Ignition switch ON 11 to 14 V
C24-3 (OXH1) - C24-32 (E1) R-B - W-B Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C24-8 (N2+) - C24-28 (N2-) G - R Camshaft position sensor Idling Pulse generation
(See waveform 4)
C24-9 (N+) - C24-29 (N-) W - B Crankshaft position sensor Idling Pulse generation
(See waveform 5)
C24-11 (OX) - C24-33 (E2) B - BR Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 6)
C24-12 (PIM) - C24-35 (E2PM) R-W - P Manifold absolute pressure sensor Sensor air released 3.1 to 4.1 V
Idling 1.2 to 2.0 V
C24-13 (KNK) - C24-33 (E2) W - BR Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 7)
C24-14 (THW) - C24-33 (E2) B-W - BR Engine coolant temperature sensor After warming up engine, Engine coolant temperature 60°C to 120°C (140°F to 248°F) 0.3 to 1.3 V
C24-15 (THA) - C24-33 (E2) G-W - BR Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
Idling, Intake air temperature 60°C (140°F) 0.2 to 1.0 V
C24-16 (VC) - C24-33 (E2) L-R - BR Power source of throttle position sensor Ignition switch ON 4.5 to 5.5 V
C24-17 (VCPM) - C24-35 (E2PM) LG - P Power source of manifold absolute pressure sensor Ignition switch ON 4.5 to 5.5 V
C24-23 (VTHO) - C24-33 (E2) V - BR Throttle position sensor Ignition switch ON, Accelerator pedal released 0.4 to 0.8 V
Ignition switch ON, Accelerator pedal depressed 3.2 to 4.8 V
E3-2 (HCAN) - E3-1 (LCAN) B - W Diagnostics tester communication Idling Pulse generation
(See waveform 8)
E3-4 (CANH) - E3-3 (CANL) R - G CAN communication signal with TCM Idling Pulse generation
(See waveform 9)
E3-6 (DEF)*1 - C24-32 (E1) G - W-B Rear window defogger switch assembly Rear window defogger switch on 11 to 14 V
Rear window defogger switch off Below 0.5 V
E3-7 (BAT) - C24-32 (E1) B - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
E3-10 (H/L)*2 - C24-32 (E1) R-L - W-B Headlight dimmer switch assembly Headlight dimmer switch on 11 to 14 V
Headlight dimmer switch off Below 0.5 V
E3-11 (BLW) - C24-32 (E1) L-R - W-B Blower with fan motor sub-assembly Blower switch on Below 0.5 V
Blower switch off 11 to 14 V
E3-12 (STP) - C24-32 (E1) G - W-B Stop light switch assembly Brake pedal depressed 11 to 14 V
Brake pedal released Below 0.5 V
E3-13 (FROF)*3 - C24-32 (E1) L - W-B Center airbag sensor assembly Idling with warm engine Pulse generation
(See waveform 10)
E3-14 (ACEV) - E3-31 (E21) W-R - R-G No. 1 cooler thermistor Air conditioner on 0.15 to 4.8 V
E3-15 (MGC) - C24-7 (E01) G-W - W-B Compressor and magnetic clutch Compressor and magnetic clutch on Below 1.0 V
Compressor and magnetic clutch off 11 to 14 V
E3-16 (FAN) - C24-7 (E01) R-W - W-B Cooling fan motor Cooling fan motor on Below 1.0 V
Cooling fan motor off 11 to 14 V
E3-17 (FC2)*4 - C24-7 (E01) B-W - W-B Fuel pump control Ignition switch ON (Not engine running) 11 to 14 V
Idling Below 2.0 V
E3-18 (FC1)*5 - C24-7 (E01) B-W - W-B Fuel pump control Ignition switch ON (Not engine running) 11 to 14 V
Idling Below 2.0 V
E3-20 (EPS)- C24-32 (E1) P - W-B Power steering ECU assembly Ignition switch ON
Steering wheel is turned from center (no load) to fully turned position
11 to 14 V → Below 1 V
E3-22 (SPD)*6 - C24-32 (E1) LG-B - W-B Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(See waveform 11)
E3-24 (ATNE)*7 - C24-32 (E1) W-L - W-B Engine revolution signal to TCM Idling Pulse generation
(See waveform 12)
E3-25 (STA) - C24-32 (E1) L-W - W-B Starter signal Cranking 6 V or more
Idling Below 0.5 V
E3-26 (T) - C24-32 (E1) LG - W-B Terminal T of DLC3 Ignition switch ON 11 to 14 V
E3-27 (W) - C24-7 (E01) V-W - W-B Malfunction indicator lamp (MIL) MIL comes on Below 1.0 V
MIL comes off 11 to 14 V
E3-29 (ACSW) - C24-32 (E1) L-Y - W-B Pressure switch Ignition switch ON 11 to 14 V
E3-30 (ACVR)*8 - E3-31 (E21) B-Y - R-G Heater control assembly (A/C volume switch) Ignition switch ON Varies with volume
E3-32 (SIO2)*4 - C24-32 (E1) P-B - R-G Transponder key ECU communication Ignition switch ON Pulse generation
E3-33 (REV) - C24-32 (E1) V-R - W-B Engine revolution signal Idling Pulse generation
(See waveform 13)

*1: w/ Rear Window Defogger

*2: w/o Multi Information Display

*3: w/ Supplemental Restraint System

*4: w/ Engine Immobilizer System

*5: w/o Engine Immobilizer System

*6: for Manual Transmission

*7: for Automatic Transmission

*8: w/o Heater


b.
A141947N04
0.354,0.188 1.219,0.708 0.865,0.521 10 10 V/DIV 0.292,1.469 0.854,1.865 0.563,0.396 10 GND 1.656,1.854 2.688,2.167 1.031,0.313 10 1 msec./DIV

Waveform 1:

Fuel Injector No. 1 (to No. 4) Injection Signal
Terminal No. (Symbol) Tool Setting Condition
C23-1 (#40) - C24-7 (E01) 10 V/DIV, 1 msec./DIV Idling
C23-2 (#30) - C24-7 (E01) 10 V/DIV, 1 msec./DIV Idling
C23-3 (#20) - C24-7 (E01) 10 V/DIV, 1 msec./DIV Idling
C23-4 (#10) - C24-7 (E01) 10 V/DIV, 1 msec./DIV Idling

HINT:

The wavelength becomes shorter as engine rpm increases.



c.
A141946N03
0.271,1.073 0.938,1.51 0.667,0.438 10 GND 0.438,0.156 1.313,0.615 0.875,0.458 10 5 V/DIV 1.552,1.854 2.604,2.177 1.052,0.323 10 1 msec./DIV

Waveform 2:

Camshaft Timing Oil Control Valve (OCV)
Terminal No. (Symbol) Tool Setting Condition
C23-6 (OCV+) - C23-5 (OCV-) 5 V/DIV, 1 msec./DIV Idling


d.
A287220N03
0.177,0.135 1.229,0.563 1.052,0.427 10 10 V/DIV 0.24,1.354 0.823,1.76 0.583,0.406 10 GND 1.542,1.729 2.771,2.135 1.229,0.406 10 20 msec./DIV

Waveform 3:

Purge VSV
Terminal No. (Symbol) Tool Setting Condition
C23-24 (PRG) - C24-7 (E01) 10 V/DIV, 20 msec./DIV Revving up

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



e.
A149567N03
0.375,0.969 0.938,1.313 0.563,0.344 10 GND 0.271,0.25 1.125,0.729 0.854,0.479 10 2 V/DIV 1.635,1.844 2.75,2.156 1.115,0.313 10 20 msec./DIV

Waveform 4:

Camshaft Position Sensor
Terminal No. (Symbol) Tool Setting Condition
C24-8 (N2+) - C24-28 (N2-) 2 V/DIV, 20 msec./DIV Idling

HINT:

The wavelength becomes shorter as engine rpm increases.



f.
A149566N03
0.302,0.302 1.042,0.708 0.74,0.406 10 2 V/DIV 1.646,1.854 2.802,2.177 1.156,0.323 10 20 msec./DIV 0.375,0.979 0.927,1.323 0.552,0.344 10 GND

Waveform 5:

Crankshaft Position Sensor
Terminal No. (Symbol) Tool Setting Condition
C24-9 (N+) - C24-29 (N-) 2 V/DIV, 20 msec./DIV Idling

HINT:

The wavelength becomes shorter as engine rpm increases.



g.
A287221N03
0.531,0.167 1.656,0.75 1.125,0.583 10 0.2 V/DIV 0.542,1.531 1.177,2.083 0.635,0.552 10 GND 1.677,1.833 2.927,2.156 1.25,0.323 10 200 msec./DIV

Waveform 6:

Heated Oxygen Sensor
Terminal No. (Symbol) Tool Setting Condition
C24-11 (OX) - C24-33 (E2) 0.2 V/DIV, 200 msec./DIV Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor


h.
A287225N04
0.198,0.385 0.927,0.854 0.729,0.469 10 1 V/DIV 0.323,1.26 0.885,1.625 0.563,0.365 10 GND 1.646,1.854 2.729,2.167 1.083,0.313 10 2 msec./DIV

Waveform 7:

Knock Sensor
Terminal No. (Symbol) Tool Setting Condition
C24-13 (KNK) - C24-33 (E2) 1 V/DIV, 2 msec./DIV Engine speed maintained at 4000 rpm after warming up engine


i.
A149563N03
0.25,1.375 0.844,1.76 0.594,0.385 10 GND 0.24,0.208 1.063,0.542 0.823,0.333 10 1 V/DIV 1.333,1.833 2.635,2.177 1.302,0.344 10 100 μsec./DIV

Waveform 8:

Reference: CAN Communication Signal (Communication with Diagnostic Tester)
Terminal No. (Symbol) Tool Setting Condition
E3-2 (HCAN) - E3-1 (LCAN) 1 V/DIV, 100 μsec./DIV Idling

HINT:

The waveform varies depending on the CAN communication signal.



j.
A149564N03
0.219,1.375 0.75,1.688 0.531,0.313 10 GND 0.177,0.208 0.906,0.625 0.729,0.417 10 1 V/DIV 1.385,1.844 2.688,2.177 1.302,0.333 10 100 μsec./DIV

Waveform 9:

Reference: CAN Communication Signal (Communication with TCM)
Terminal No. (Symbol) Tool Setting Condition
E3-4 (CANH) - E3-3 (CANL) 1 V/DIV, 100 μsec./DIV Idling

HINT:

The waveform varies depending on the CAN communication signal.



k.
A288852N02
0.302,1.167 0.76,1.365 0.458,0.198 10 GND 0.427,0.125 1.208,0.469 0.781,0.344 10 2 V/DIV 1.656,1.948 2.708,2.177 1.052,0.229 10 500 msec./DIV

Waveform 10:

Center Airbag Sensor Assembly
Terminal No. (Symbol) Tool Setting Condition
E3-13 (FROF) - E24-32 (E1) 2 V/DIV, 500 μsec./DIV Idling with warm engine

HINT:

If the airbag is deployed, a contact voltage is inputted to the ECM.



l.
A287222N03
0.521,0.271 1.188,0.677 0.667,0.406 10 2 V/DIV 0.448,1.156 0.906,1.458 0.458,0.302 10 GND 1.75,1.875 2.938,2.177 1.188,0.302 10 20 msec./DIV

Waveform 11:

Speed Signal from Combination Meter
Terminal No. (Symbol) Tool Setting Condition
E3-22 (SPD) - C24-32 (E1) 2 V/DIV, 20 msec./DIV Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as vehicle speed increases.



m.
A287223N05
0.25,0.198 1.021,0.51 0.771,0.313 10 5 V/DIV 0.198,1.042 0.76,1.438 0.563,0.396 10 GND 1.594,1.74 2.802,2.021 1.208,0.281 10 10 msec./DIV

Waveform 12:

Engine Revolution Signal to TCM
Terminal No. (Symbol) Tool Setting Condition
E3-24 (ATNE) - C24-32 (E1) 5 V/DIV, 10 msec./DIV Engine idling speed (When measured waveform 2000 rpm)

HINT:

The wavelength becomes shorter as engine rpm increases.



n.
A287223N06
0.25,0.198 1.021,0.51 0.771,0.313 10 5 V/DIV 0.198,1.042 0.76,1.438 0.563,0.396 10 GND 1.594,1.74 2.802,2.021 1.208,0.281 10 10 msec./DIV

Waveform 13:

Engine Revolution Signal
Terminal No. (Symbol) Tool Setting Condition
E3-33 (REV) - C24-32 (E1) 5 V/DIV, 10 msec./DIV Idling

HINT:

The wavelength becomes shorter as engine rpm increases.