CHECK ECM
Measure the voltage according to the value(s) in the table below.
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C23-1 (#40) - C24-7 (E01) | V - W-B | Fuel injector assembly | Ignition switch ON | 11 to 14 V |
| C23-2 (#30) - C24-7 (E01) | R - W-B | |||
| C23-3 (#20) - C24-7 (E01) | P - W-B | Idling | Pulse generation
(See waveform 1) |
|
| C23-4 (#10) - C24-7 (E01) | W-R - W-B | |||
| C23-6 (OCV+) - C23-5 (OCV-) | G - LG | Camshaft timing oil control valve assembly | Idling | Pulse generation
(See waveform 2) |
| C23-7 (+B1) - C24-32 (E1) | L - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| C23-9 (IG4) - C24-32 (E1) | L - W-B | Ignition coil assembly
(Ignition signal) |
Ignition switch ON | Below 0.5 V |
| C23-10 (IG3) - C24-32 (E1) | G - W-B | |||
| C23-11 (IG2) - C24-32 (E1) | R - W-B | Idling | Pulse generation
(See page ) |
|
| C23-12 (IG1) - C24-32 (E1) | B - W-B | |||
| C23-13 (OXH2) - C24-32 (E1) | L-R - W-B | Heated oxygen sensor heater (sensor 2) | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| C23-15 (IAHI) - C23-14 (IALO) | V - G-W | Idle speed control valve | Idling, air conditioning OFF or ON | Pulse generation
(0 to 12 V) |
| C23-17 (IBHI) - C23-16 (IBLO) | LG - P | |||
| C23-24 (PRG) - C24-7 (E01) | W - W-B | Purge VSV | Ignition switch ON | 11 to 14 V |
| Idling, under purge operation | Pulse generation
(See waveform 3) |
|||
| C23-34 (ALT) - C24-32 (E1) | B-W - W-B | Generator assembly | Ignition switch ON | 11 to 14 V |
| C24-3 (OXH1) - C24-32 (E1) | R-B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| C24-8 (N2+) - C24-28 (N2-) | G - R | Camshaft position sensor | Idling | Pulse generation
(See waveform 4) |
| C24-9 (N+) - C24-29 (N-) | W - B | Crankshaft position sensor | Idling | Pulse generation
(See waveform 5) |
| C24-11 (OX) - C24-33 (E2) | B - BR | Heated oxygen sensor | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(See waveform 6) |
| C24-12 (PIM) - C24-35 (E2PM) | R-W - P | Manifold absolute pressure sensor | Sensor air released | 3.1 to 4.1 V |
| Idling | 1.2 to 2.0 V | |||
| C24-13 (KNK) - C24-33 (E2) | W - BR | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(See waveform 7) |
| C24-14 (THW) - C24-33 (E2) | B-W - BR | Engine coolant temperature sensor | After warming up engine, Engine coolant temperature 60°C to 120°C (140°F to 248°F) | 0.3 to 1.3 V |
| C24-15 (THA) - C24-33 (E2) | G-W - BR | Intake air temperature sensor | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| Idling, Intake air temperature 60°C (140°F) | 0.2 to 1.0 V | |||
| C24-16 (VC) - C24-33 (E2) | L-R - BR | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C24-17 (VCPM) - C24-35 (E2PM) | LG - P | Power source of manifold absolute pressure sensor | Ignition switch ON | 4.5 to 5.5 V |
| C24-23 (VTHO) - C24-33 (E2) | V - BR | Throttle position sensor | Ignition switch ON, Accelerator pedal released | 0.4 to 0.8 V |
| Ignition switch ON, Accelerator pedal depressed | 3.2 to 4.8 V | |||
| C24-24 (OX2) - C24-33 (E2) | W - BR | Heated oxygen sensor (sensor 2) | Engine speed maintained at 2,500 rpm for 3 minutes after warming up sensor | Pulse generation
(See waveform 8) |
| E3-2 (HCAN) - E3-1 (LCAN) | B - W | Diagnostics tester communication | Idling | Pulse generation
(See waveform 9) |
| E3-4 (CANH) - E3-3 (CANL) | R - G | CAN communication signal with TCM | Idling | Pulse generation
(See waveform 10) |
| E3-6 (DEF)*1 - C24-32 (E1) | G - W-B | Rear window defogger switch assembly | Rear window defogger switch on | 11 to 14 V |
| Rear window defogger switch off | Below 0.5 V | |||
| E3-7 (BAT) - C24-32 (E1) | B - W-B | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| E3-10 (H/L)*2 - C24-32 (E1) | R-L - W-B | Headlight dimmer switch assembly | Headlight dimmer switch on | 11 to 14 V |
| Headlight dimmer switch off | Below 0.5 V | |||
| E3-11 (BLW) - C24-32 (E1) | L-R - W-B | Blower with fan motor sub-assembly | Blower switch on | Below 0.5 V |
| Blower switch off | 11 to 14 V | |||
| E3-12 (STP) - C24-32 (E1) | G - W-B | Stop light switch assembly | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 0.5 V | |||
| E3-13 (FROF)*3 - C24-32 (E1) | L - W-B | Center airbag sensor assembly | Idling with warm engine | Pulse generation
(See waveform 11) |
| E3-14 (ACEV) - E3-31 (E21) | W-R - R-G | No. 1 cooler thermistor | Air conditioner on | 0.15 to 4.8 V |
| E3-15 (MGC) - C24-7 (E01) | G-W - W-B | Compressor and magnetic clutch | Compressor and magnetic clutch on | Below 1.0 V |
| Compressor and magnetic clutch off | 11 to 14 V | |||
| E3-16 (FAN) - C24-7 (E01) | R-W - W-B | Cooling fan motor | Cooling fan motor on | Below 1.0 V |
| Cooling fan motor off | 11 to 14 V | |||
| E3-17 (FC2)*4 - C24-7 (E01) | B-W - W-B | Fuel pump control | Ignition switch ON (Not engine running) | 11 to 14 V |
| Idling | Below 2.0 V | |||
| E3-18 (FC1)*5 - C24-7 (E01) | B-W - W-B | Fuel pump control | Ignition switch ON (Not engine running) | 11 to 14 V |
| Idling | Below 2.0 V | |||
| E3-20 (EPS)- C24-32 (E1) | P - W-B | Power steering ECU assembly | Ignition switch ON
Steering wheel is turned from center (no load) to fully turned position |
11 to 14 V → Below 1 V |
| E3-22 (SPD)*6 - C24-32 (E1) | LG-B - W-B | Speed signal from combination meter | Driving at 20 km/h (12 mph) | Pulse generation
(See waveform 12) |
| E3-24 (ATNE)*7 - C24-32 (E1) | W-L - W-B | Engine revolution signal to TCM | Idling | Pulse generation
(See waveform 13) |
| E3-25 (STA) - C24-32 (E1) | L-W - W-B | Starter signal | Cranking | 6 V or more |
| Idling | Below 0.5 V | |||
| E3-26 (T) - C24-32 (E1) | LG - W-B | Terminal T of DLC3 | Ignition switch ON | 11 to 14 V |
| E3-27 (W) - C24-7 (E01) | V-W - W-B | Malfunction indicator lamp (MIL) | MIL comes on | Below 1.0 V |
| MIL comes off | 11 to 14 V | |||
| E3-29 (ACSW) - C24-32 (E1) | L-Y - W-B | Pressure switch | Ignition switch ON | 11 to 14 V |
| E3-30 (ACVR)*8 - E3-31 (E21) | B-Y - R-G | Heater control assembly (A/C volume switch) | Ignition switch ON | Varies with volume |
| E3-32 (SIO2)*4 - C24-32 (E1) | P-B - R-G | Transponder key ECU communication | Ignition switch ON | Pulse generation |
| E3-33 (REV) - C24-32 (E1) | V-R - W-B | Engine revolution signal | Idling | Pulse generation
(See waveform 14) |
*1: w/ Rear Window Defogger
*2: w/o Multi Information Display
*3: w/ Supplemental Restraint System
*4: w/ Engine Immobilizer System
*5: w/o Engine Immobilizer System
*6: for Manual Transmission
*7: for Automatic Transmission
*8: w/o Heater
Waveform 1:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-1 (#40) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-2 (#30) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-3 (#20) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
| C23-4 (#10) - C24-7 (E01) | 10 V/DIV, 1 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 2:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-6 (OCV+) - C23-5 (OCV-) | 5 V/DIV, 1 msec./DIV | Idling |
Waveform 3:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C23-24 (PRG) - C24-7 (E01) | 10 V/DIV, 20 msec./DIV | Revving up |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
Waveform 4:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-8 (N2+) - C24-28 (N2-) | 2 V/DIV, 20 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 5:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-9 (N+) - C24-29 (N-) | 2 V/DIV, 20 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.
Waveform 6:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-11 (OX) - C24-33 (E2) | 0.2 V/DIV, 200 msec./DIV | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
Waveform 7:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-13 (KNK) - C24-33 (E2) | 1 V/DIV, 2 msec./DIV | Engine speed maintained at 4000 rpm after warming up engine |
Waveform 8:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-24 (OX2) - C24-33 (E2) | 0.2 V/DIV, 200 msec./DIV | Engine speed maintained at 2,500 rpm for 3 minutes after warming up sensor |
Waveform 9:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-2 (HCAN) - E3-1 (LCAN) | 1 V/DIV, 100 μsec./DIV | Idling |
The waveform varies depending on the CAN communication signal.
Waveform 10:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-4 (CANH) - E3-3 (CANL) | 1 V/DIV, 100 μsec./DIV | Idling |
The waveform varies depending on the CAN communication signal.
Waveform 11:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-13 (FROF) - C24-32 (E1) | 2 V/DIV, 500 msec./DIV | Idling with warm engine |
If the airbag is deployed, a constant voltage is inputted to the ECM.
Waveform 12:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-22 (SPD) - C24-32 (E1) | 2 V/DIV, 20 msec./DIV | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as vehicle speed increases.
Waveform 13:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-24 (ATNE) - C24-32 (E1) | 5 V/DIV, 10 msec./DIV | Engine idling speed (When measured waveform 2000 rpm) |
The wavelength becomes shorter as engine rpm increases.
Waveform 14:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| E3-33 (REV) - C24-32 (E1) | 5 V/DIV, 10 msec./DIV | Idling |
The wavelength becomes shorter as engine rpm increases.