Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) U

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

By reading the Data List displayed on the intelligent tester or Techstream, values can be checked, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.


NOTICE:

In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester or Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester or Techstream on.


f.

Enter the following menus: Powertrain / Engine / Data List.


g.

According to the display on the intelligent tester or Techstream, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IGN Advance Ignition timing advance for No. 1 cylinder Min.: -64 deg, Max.: 63.5 deg BTDC 0 to 10 deg (neutral position):
Idling
Read value with A/C OFF and shift lever N position
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Calculate Load Calculated load by ECM Min.: 0 %, Max.: 100 % 10 to 20 %: Idling (A/C OFF, neutral position) -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MAP Manifold absolute pressure Min.: 0 kPa, Max.: 255 kPa 70 to 104 kPa: Ignition switch ON (engine not started)
20 to 40 kPa: Idling
If value approximately 0 kPa:
·

PIM circuit short


If value 120 kPa or more:
·

VCPM circuit open or short

·

PIM circuit open

·

E2PM circuit open


HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Idle Engine Speed Target idle engine speed Min.: 0 rpm, Max.: 51199 rpm 700 to 800 rpm (neutral position): Idling -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383.75 rpm 700 to 800 rpm (neutral position): Idling -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature Min.: -40°C, Max.: 215°C 80 to 102°C (176 to 215°F):
After warming up engine
·

If value -30°C (-22°F) or less: sensor circuit open

·

If value 130°C (266°F) or more: sensor circuit shorted


HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intake Air Intake air temperature Min.: -40°C, Max.: 140°C Equivalent to ambient air temperature
·

If value -30°C (-22°F) or less: sensor circuit open

·

If value 130°C (266°F) or more: sensor circuit shorted


HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Initial Engine Coolant Temp Initial engine coolant temperature Min.: -40°C, Max.: 215°C Coolant temperature when engine started This is the coolant temperature stored when the power switch is turned to ON.
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Initial Intake Air Temp Initial intake air temperature Min.: -40°C, Max.: 215°C Intake air temperature when engine started This is the intake air temperature stored when the power switch is turned to ON.
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Run Time Engine run time Min.: 0 s (seconds), Max.: 65535 s (seconds) Time after engine start This is the time elapsed since the engine started.
HINT:
·

The time is counted only while the engine is running.

·

Stored as Freeze Frame Data : Yes



Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EVAP (Purge) VSV Vacuum switching valve (EVAP) control duty Min.: 0 %, Max.: 100 % 0 to 40 %: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Purge Correct Value Purge trim ratio Min.: -50%, Max.: 349.99% 0: Idling with warmed up engine -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Throttle Position Absolute throttle valve opening angle Min.: 0 %, Max.: 100 %
·

0 to 15 %: Throttle fully closed

·

70 to 100 %: Throttle fully open


Read value with ignition switch ON (Do not start engine)
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Throttle Sensor Position Relative throttle valve opening angel Min.: 0 %, Max.: 100 % 0 to 10 %: Idling Calculated value based on VTH
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2S B1 S1 Heated oxygen sensor output voltage for sensor 1 Min.: 0 V, Max.: 1.275 V 0.1 to 0.95 V:
Driving (50 km/h, 31 mph)
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2S B1 S2 Heated oxygen sensor output voltage for sensor 2 Min.: 0 V, Max.: 1.275 V 0.1 to 0.95 V:
Driving (50 km/h, 31 mph)
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Short FT #1 Short-term fuel trim (bank 1) Min.: -100 %, Max.: 99.2 % -20 to 20 %: Engine speed constant 2500 rpm Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Long FT #1 Long-term fuel trim (bank 1) Min.: -100 %, Max.: 99.2 % -30 to 30 %: Engine speed constant 2500 rpm Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Fuel Trim Total fuel trim for bank 1 (Average value for fuel trim system of bank 1) Min.: 0, Max.: 1.999 - Total FT #1 = Short FT #1 + Long FT #1
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel System Status (Bank1) Fuel system status (bank 1) Unused / OL / CL / OLDrive CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop

·

CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control

·

OLDRIVE: Open loop due to driving conditions (fuel enrichment)


HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2FT B1 S1 Short-term fuel trim associated with bank 1 sensor 1 Min.: -100 %, Max.: 99.2 % -20 to 20 %:
Engine speed constant 2500 rpm
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2FT B1 S2 Short-term fuel trim associated with bank 1 sensor 2 Min.: -100 %, Max.: 99.2 % -30 to 30 %:
Engine speed constant 2500 rpm
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Injection Volume Injection volume of No.1 cylinder (cumulative value for 10 times) Min.: 0 ml, Max.: 2.047 ml 0.003 to 0.015 ml: Idling Read value with A/C OFF and shift lever N position
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Injection Time Injection period of No.1 cylinder Min.: 0 ms, Max.: 32.64 ms 3 to 8 ms: Idling with cold engine
2 to 4 ms: Idling with warmed up engine
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Steering Signal Power steering signal OFF / ON ON: When turning steering wheel -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Signal Air conditioner signal OFF / ON ON: A/C ON -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Electrical Load Signal Electrical load signal OFF / ON ON: Tail light switch ON
ON: Defogger switch ON
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Signal Stop light switch OFF / ON ON: When operating brake -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2 Sensor Signal Status of air-fuel ratio Lean / Rich - -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Idling Signal Whether throttle position sensor detecting idling OFF / ON ON: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Atmosphere Pressure Atmospheric pressure Min.: 0 kPa, Max.: 255 kPa 70 to 110 kPa: Ignition switch ON -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intake Manifold Pressure Actual air intake pressure Min.: 0 kPa, Max.: 65535 kPa 80 to 110 kPa: Ignition switch ON (Engine not started)
20 to 40 kPa: Idling
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ISC STEP Position Idle speed control valve step position Min.: 0 step, Max.: 255 step Depending on engine running condition -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ISC Duty Idle speed control valve control duty ratio Min.: 0 %, Max.: 99.6 % - -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VVT Aim Angle (Bank1) VVT aim angle (bank 1) Min.: 0 deg, Max.: 639.99 deg 0 to 5 deg: Idling
10 to 40 deg: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VVT Change Angle (Bank1) VVT change angle (bank 1) Min.: 0 deg, Max.: 639.99 deg 0 to 5 deg: Idling
10 to 40 deg: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VVT Calc Angle (Bank1) VVT calculated angle (bank 1) Min.: 0 deg, Max.: 639.99 deg 15 to 52 deg: Idling
15 to 82 deg: 2000 rpm (fixed speed)
-
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VVT Control Duty (Bank1) VVT OCV control duty Min.: 0 %, Max.: 399.99 % 20 to 50 %: 2000 rpm (fixed speed) -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Knock Correct Angle Knock control correction advance angle Min.: -64 CA, Max.: 1983.9 CA 0 to 3 CA: Idling -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Signal Shift position signal received from transmission control ECU N / R / 1st / 2nd / 3rd / 4th - -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal OFF / ON ON: Cranking -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cylinder #1 Misfire Count Misfire count of cylinders 1 Min.: 0, Max.: 255 0 This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #2 Misfire Count Misfire count of cylinders 2 Min.: 0, Max.: 255 0 This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #3 Misfire Count Misfire count of cylinders 3 Min.: 0, Max.: 255 0 This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.
HINT:

Stored as Freeze Frame Data : Yes


Cylinder #4 Misfire Count Misfire count of cylinders 4 Min.: 0, Max.: 255 0 This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Evaporator Temperature A/C evaporator temperature Min.: -80°C, Max.: 943.98°C Actual A/C evaporator temperature displayed -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
# Codes Number of detected DTCs Min.: 0, Max.: 255 0 -
HINT:

Stored as Freeze Frame Data : Yes


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MIL Malfunction Indicator Lamp (MIL) status OFF / ON OFF -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MIL ON Run Distance Distance traveled since MIL turned ON Min.: 0 Km, Max.: 65535 Km Distance after DTC detected -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Number of Emission DTC Number of emission related DTCs Min.: 0, Max.: 127 - -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Component Monitor ENA Comprehensive component monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


Component Monitor CMPL Comprehensive component monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


Fuel System Monitor ENA Fuel system monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


Fuel System Monitor CMPL Fuel system monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


Misfire Monitor ENA Misfire monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


Misfire Monitor CMPL Misfire monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Heater Monitor ENA Heated oxygen sensor (air-fuel ratio sensor) heater monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


Heater Monitor CMPL Heated oxygen sensor (air-fuel ratio sensor) heater monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


O2S(A/FS) Monitor ENA Heated oxygen sensor (air-fuel ratio sensor) monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


O2S(A/FS) Monitor CMPL Heated oxygen sensor (air-fuel ratio sensor) monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


EVAP Monitor ENA EVAP system monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


EVAP Monitor CMPL EVAP system monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


Catalyst Monitor ENA Catalyst monitor applicability Not Avl / Avail - -
HINT:

Stored as Freeze Frame Data : No


Catalyst Monitor CMPL Catalyst monitor Compl / Incmpl - -
HINT:

Stored as Freeze Frame Data : No


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ISC Learning Value ISC Learning Value Min.: 0 Lys, Max.: 79.99 Lys 0.4 to 1.23 Lys: Idling -
HINT:

Stored as Freeze Frame Data : Yes




ACTIVE TEST


HINT:

Performing an Active Test enables components including the relays, Vacuum switching valve and actuators, to be operated without removing any parts. The Active Test can be performed with the intelligent tester or Techstream. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time.


Data List can be displayed during Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch to off.


c.

Connect the intelligent tester or Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester or Techstream on.


f.

Enter the following menus: Powertrain / Engine / Active Test.


g.

According to the display on the intelligent tester or Techstream, perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
Control the ISC Step Position Min.: 10 step, Max.: 100 step Idle speed control valve (stepper motor) Vehicle: Stationary
Engine speed: Idling
Battery voltage: 8.5 V or more
Control the ISC Value Min.: 5 %, Max.: 50 % Idle speed control valve (rotary solenoid) Unused
Activate the Fuel Pump Speed Control ON or OFF Fuel pump relay (F/P relay) -
Activate the VSV for Purge Control ON or OFF Vacuum switching valve (EVAP) -
Control the Cooling Fan ON or OFF Radiator fan motor -
Connect the TC and TE1 ON or OFF Turn on and off EFIT and E connection ON: EFIT and E terminals of DLC3 are connected.
OFF: EFIT and E terminals of DLC3 are disconnected.
Control the A/C Magnet Clutch ON or OFF Air conditioner magnet clutch -