Home › Engine / Hybrid System › 3SZ-VE ENGINE MECHANICAL › CYLINDER HEAD › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002969 3SZ-VE ENGINE MECHANICAL _0015000 CYLINDER HEAD A

3SZ-VE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL TIGHT PLUG

A143044N01
1.854,1.469 1.854,1.156 false 1.708,1.49 2.292,1.854 0.583,0.365 10 SST

a.

Apply adhesive to the outer surface of a new tight plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Using SST, install the tight plug until its height is as illustrated.

Standard depth:

0.1 to 1.0 mm (0.004 to 0.039 in.)


SST
09950-60010  (09951-00220, 09951-00260)
09950-70010  (09951-07100)

A143045C04
4.885,1.865 6.323,2.25 1.438,0.385 10 0.1 mm to 1.0 mm 1.396,1.865 2.906,2.25 1.51,0.385 10 0.1 mm to 1.0 mm 4.229,0.167 4.688,0.583 0.458,0.417 10 *b 0.396,0.156 0.906,0.521 0.51,0.365 10 *a
*a Front Side View *b Rear Side View



Hide 2.INSTALL RING PIN

A143046E03
1.802,2.625 3.063,3 1.26,0.375 10 2.0 to 3.0 mm

a.

Using a plastic-faced hammer, tap in new ring pins until its protrusion height is as specified.

Protrusion height:

2.0 to 3.0 mm (0.079 to 0.118 in.)



Hide 3.INSTALL STUD BOLT

a.

Install the stud bolts in the positions shown in the illustration.

A266106C04
1.021,0.958 1.021,1.25 true 5.823,1.313 5.823,1.625 true 1,2.063 1.938,2.813 1.938,2.813 2.979,2.052 true 1.313,4.323 1.885,5.01 1.885,5.01 2.313,4.333 true 4.302,2.823 5.167,3.302 5.167,3.302 6.021,2.844 true 0.979,1.271 1.354,1.635 0.375,0.365 10 A 5.792,1.677 6.073,2.042 0.281,0.365 10 B 1.896,2.865 2.198,3.198 0.302,0.333 10 C 5.135,3.344 5.49,3.625 0.354,0.281 10 D 1.844,5.083 2.135,5.396 0.292,0.313 10 E 0.313,6.406 0.969,6.823 0.656,0.417 10 A (M6) 0.302,7.385 1.021,7.76 0.719,0.375 10 C (M8) 2.5,6.396 3.177,6.781 0.677,0.385 10 B (M6) 2.573,7.365 3.313,7.729 0.74,0.365 10 D (M8) 4.781,7 5.563,7.396 0.781,0.396 10 E (M6) 0.802,5.677 1.26,6.083 0.458,0.406 10 *a 0.833,6.188 1.271,6.604 0.438,0.417 10 *b 1.354,5.917 1.813,6.292 0.458,0.375 10 *c 2.99,5.823 3.385,6.156 0.396,0.333 10 *d 3.521,5.99 3.917,6.333 0.396,0.344 10 *f 2.99,6.156 3.438,6.531 0.448,0.375 10 *e 1.333,7.156 1.74,7.5 0.406,0.344 10 *g 1.323,7.542 1.74,7.813 0.417,0.271 10 *h 1.865,7.365 2.25,7.677 0.385,0.313 10 *i 3.583,7.219 3.969,7.563 0.385,0.344 10 *j 3.583,7.542 4,7.813 0.417,0.271 10 *k 4.25,7.375 4.771,7.75 0.521,0.375 10 *l 5.75,6.5 6.229,6.875 0.479,0.375 10 *M 5.771,7.583 6.229,7.823 0.458,0.24 10 *N 6.281,7.021 6.823,7.458 0.542,0.438 10 *O
*a 12 mm (0.4724 in.) *b 7 mm (0.2756 in.) *
*c 37 mm (1.4567 in.) *d 12 mm (0.4724 in.)
*e 12 mm (0.4724 in.) *f 30 mm (1.1811 in.)
*g 12 mm (0.4724 in.) *h 12 mm (0.4724 in.)
*i 37 mm (1.4567 in.) *j 13.5 mm (0.5315 in.)
*k 13.5 mm (0.5315 in.) *l 29 mm (1.1417 in.)
*m 9 mm (0.3543 in.) *n 9 mm (0.3543 in.)
*o 66.9 mm (2.6339 in.) - -


*: Cylinder head side

Torque:
A,B,E : 4.0 N*m (41 kgf*cm, 35 in.*lbf)
C,D : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 4.INSTALL UNION

A143048C04
1.219,1.948 1.677,2.292 0.458,0.344 10 *a 2.896,1.833 3.188,2.198 0.292,0.365 10 *b 0.667,3.125 1.146,3.521 0.479,0.396 10 *c
*a 45.2 to 47.2 mm (1.7795 to 1.8583 in.)
*b 42 to 44 mm (1.6535 to 1.7323 in.)
*c 31°+/-5°(w/ heater) 49°+/-5°(w/o heater)


a.

Apply adhesive to the inside of the holes in the cylinder head.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Using a press, press in a new union until its height is as illustrated.

NOTICE:
·

Install the union within 3 minutes of applying the adhesive.

·

Do not expose the adhesive to coolant for at least 1 hour after installation.




Hide 5.INSTALL VALVE SEAT

Hide 13711A 6.INSTALL VALVE STEM OIL O SEAL OR RING

a.

Apply a light coat of engine oil to the lip of a new valve stem oil o seal or ring.


b.
A143049C04
1.771,1.302 2.698,1.948 true 2.74,1.979 3.323,2.396 0.583,0.417 10 SST 1.49,3.188 1.896,3.563 0.406,0.375 10 *a
*a 14.2 to 15.8 mm (0.5591 to 0.6220 in.)


Using SST, install the valve stem oil o seal or ring.

SST
09201-41020  

HINT:

After pressing in the oil seal, check that the height of the valve stem oil o seal or ring is as illustrated.



Hide 7.INSTALL VALVE

A143051C04
1.26,0.271 1.656,0.677 0.396,0.406 10 *b 2.021,0.271 2.458,0.688 0.438,0.417 10 *a
*a Valve Tip
*b 20 mm (0.7874 in.)


a.

Apply engine oil to the valve tip.


b.
A143052

Install the valve, valve spring and retainer onto the cylinder head.

NOTICE:

Install the parts onto their original locations.



c.
A137157

Using SST, install the retainer lock.

SST
09202-70020  (09202-01010, 09202-01020, 90154-80004)
09202-00020  


d.
A143053

Using a 5 mm pin punch, tap in the valve tip so that the valve spring becomes stable.

NOTICE:

Be careful not to damage the tip of the valve stem.



e.
A143054

After installing all the valve springs, apply engine oil as illustrated.


Hide 15678A 8.INSTALL OIL CONTROL VALVE FILTER

A266610

a.

Using an 8 mm socket hexagon wrench, place a new gasket on the plug and install the oil control valve filter.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 13751 9.INSTALL VALVE LIFTER

A143056

a.

Apply a light coat of engine oil to the valve lifter.

NOTICE:

Install the parts onto their original locations.



b.

Install the valve lifter onto the cylinder head.


c.

Check that the valve lifter turns smoothly.