Home › Engine / Hybrid System › 3SZ-VE ENGINE MECHANICAL › CYLINDER BLOCK › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002969 3SZ-VE ENGINE MECHANICAL _0015001 CYLINDER BLOCK A

3SZ-VE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins.

Standard protrusion:

7.0 to 8.0 mm (0.276 to 0.315 in.)


A262839C04
5.156,0.917 5.594,1.167 0.438,0.25 10 A 6.063,1.208 6.542,1.583 0.479,0.375 10 *a 5.375,1.844 5.813,2.229 0.438,0.385 10 *b
*a Height *b Width


Specification:
Area Protrusion Height Digmeter
A 7.0 to 8.0 mm (0.2756 to 0.3150 in.) 12 mm (0.4724 in.)



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap in new straight pins.

Standard protrusion:
Pin A:

3.5 to 4.5 mm (0.138 to 0.177 in.)

Pin B:

8.0 to 9.0 mm (0.315 to 0.354 in.)

Pin C:

5.5 to 6.5 mm (0.217 to 0.256 in.)


A276012C02
2.49,1.26 2.76,1.51 2.76,1.51 2.208,1.635 true 2.24,4.083 2,4.344 2,4.344 1.521,4.083 true 1.625,3.115 1.094,3 true 2.844,4.25 3.302,4.135 true 2.823,1.438 3.219,1.844 0.396,0.406 10 A 4.531,0.771 5.063,1.281 0.531,0.51 10 A 0.948,2.896 1.302,3.26 0.354,0.365 10 B 4.531,2.448 4.979,2.792 0.448,0.344 10 B 1.958,4.354 2.354,4.729 0.396,0.375 10 C 4.531,3.5 4.969,3.917 0.438,0.417 10 C 4.708,4.302 5.104,4.604 0.396,0.302 10 *b 5.333,3.656 5.698,4.031 0.365,0.375 10 *a 4.708,3.292 5.073,3.615 0.365,0.323 10 *b 5.333,2.635 5.719,3.042 0.385,0.406 10 *a 4.708,1.563 5.188,1.948 0.479,0.385 10 *b 5.333,0.938 5.708,1.333 0.375,0.396 10 *a 3.333,4.031 3.854,4.427 0.521,0.396 10 B
*a Height *b Width


Specification:
Area Protrusion Height Digmeter
A 3.5 to 4.5 mm (0.1378 to 0.1772 in.) 6.0 mm (0.2362 in.)
B 8.5 to 9.5 mm (0.3346 to 0.3740 in.) 10.0 mm (0.3937 in.)
C 5.5 to 6.5 mm (0.2165 to 0.2559 in.) 6.0 mm (0.2362 in.)