Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › DRIVE BELT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015003 DRIVE BELT G

K3-VE ENGINE MECHANICAL  DRIVE BELT  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16361A 1.INSPECT FAN AND GENERATOR V BELT

a.
A219362

Check the fan and generator V belt for wear, cracks or other signs of damage.

If any of the following defects is found, replace the fan and generator V belt.

·

The fan and generator V belt is cracked.

·

The fan and generator V belt is worn out to the extent that the cords are exposed.

·

The fan and generator V belt has chunks missing from the ribs.



b.
A219363C06
2.469,1.521 2.844,1.833 0.375,0.313 10 *b 0.51,1.521 0.885,1.844 0.375,0.323 10 *a
*a Correct
*b Incorrect


A268655C01
0.292,3.844 0.729,4.219 0.438,0.375 10 *1 0.958,3.354 1.354,3.729 0.396,0.375 10 *2 1.688,3.344 2.073,3.677 0.385,0.333 10 *3 2.281,2.688 2.688,3.052 0.406,0.365 10 *4 2.708,3.458 3.135,3.854 0.427,0.396 10 *5 1.427,4.021 1.917,4.448 0.49,0.427 10 *6 0.49,1.49 0.875,1.813 0.385,0.323 10 *1 0.969,1.104 1.302,1.406 0.333,0.302 10 *2 1.708,1.083 2.052,1.417 0.344,0.333 10 *3 2.292,0.406 2.667,0.771 0.375,0.365 10 *4 2.708,1.563 3.073,1.948 0.365,0.385 10 *5 1.438,1.76 1.802,2.104 0.365,0.344 10 *6 0.104,2.24 0.604,2.625 0.5,0.385 12 B: 0.104,0.052 0.552,0.458 0.448,0.406 12 A:
*A for RHD
*B for LHD
*1 Generator Pulley
*2 Water Pump Pulley
*3 No. 1 Idler Pulley Sub-assembly
*4 Idler Pulley Sub-assembly
*5 Cooler Compressor Assembly
*6 Crankshaft Pulley
V100135

Specified Point


Check that the fan and generator V belt fits properly in the ribbed grooves.

HINT:
·

Check with your hand to confirm that the fan and generator V belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the fan and generator V belt. Install a new fan and generator V belt correctly.

·

Check the belt deflection by pressing on the belt at the points indicated by the arrow marks in the illustration.

·

When inspecting the fan and generator V belt deflection, apply 98 N (10 kgf, 22.0 lbf) of tensile force to it.



Deflection:
Item Specified Condition
New belt 11.0 to 12.5 mm (0.43 to 0.49 in.)
Used belt 11.5 to 15.0mm (0.45 to 0.59 in.)
Adjust of used belt 11.5 to 13.0mm (0.45 to 0.51 in.)


Tension:
Item Specified Condition
New belt 588 to 686 N (60 to 70 kgf, 132 to 154 lb)
Used belt 343 to 539 N (35 to 99 kgf, 77to 121 lb)
Adjust of used belt 441 to 539 N (45 to 55 kgf, 99to 121 lb)


If the belt deflection is not as specified, adjust it.

HINT:
·

Check the fan and generator V belt deflection at the specified point.

·

When installing a new belt, set its tension to the specified value.

·

When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.

·

When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.

·

V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.

·

When using a belt tension gauge, confirm its accuracy by using a master gauge first.