Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › ENGINE UNIT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015010 ENGINE UNIT G

K3-VE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

A104129

a.

Visually check the timing chain for wear and cracks. If the timing chain is worn or cracked, replace the timing chain and check the sprocket.


b.
A162995C10
0.823,1.844 1.125,2.146 0.302,0.302 10 2 0.99,1.844 1.292,2.146 0.302,0.302 10 3 1.146,1.844 1.417,2.125 0.271,0.281 10 4 1.313,1.844 1.604,2.146 0.292,0.302 10 5 1.458,1.844 1.781,2.167 0.323,0.323 10 6 0.677,1.854 0.948,2.135 0.271,0.281 10 1 2.521,1.844 2.875,2.177 0.354,0.333 10 15 2.719,1.833 3.104,2.125 0.385,0.292 10 16 1.625,1.115 2,1.448 0.375,0.333 10 *a
*a Measuring Area


Pull the chain with a force of 225 N (22.9 kgf, 50.6 lbf) as shown in the illustration.


c.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

93.121 mm (3.6662 in.)


HINT:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is greater than the maximum, replace the chain.


Hide 13545 2.INSPECT CHAIN TENSIONER PLUNGER

A137163

a.

Check that the chain tensioner plunger moves smoothly when the stopper plate of the chain tensioner plunger is pushed by hand.


b.

Release the stopper plate. Check that the chain tensioner plunger does not move with the stopper plate locked, even if the chain tensioner plunger is pushed by hand.


Hide 13520 3.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

A137123

NOTICE:

Do not dismantle camshaft timing sprocket assembly.


a.

Clamp the camshaft in a vise.

NOTICE:

Do not damage the camshaft.



b.

Temporarily tighten the timing sprocket with the bolt.


c.
A137124C03
1.177,1.76 1.646,1.927 true 1.667,1.844 2.042,2.156 0.375,0.313 10 *a
*a Advance Port


Cover one of the 2 advance ports with your finger.


d.
A137125

Apply air pressure to the other advance port.

NOTICE:

Be careful of oil splashes.



e.
A137126N03
0.604,0.479 1.052,0.823 0.448,0.344 10 30°

Check that the lock pin is released and the timing sprocket moves smoothly within a 30° range by hand.

NOTICE:

The timing sprocket is locked in the most retarded position.



f.

Lock the timing sprocket in the most retarded position, then remove the bolt and timing sprocket.


Hide 13523 4.INSPECT CAMSHAFT TIMING GEAR OR SPROCKET

a.

Check the camshaft timing gear or sprocket for any wear or damage. If any, replace them with new ones.


Hide 13566B 5.INSPECT TIMING CHAIN GUIDE

a.

Check the timing chain guide for any wear or damage. If any, replace them with new ones.


Hide 13591 6.INSPECT TIMING CHAIN TENSION ARM

a.

Check the timing chain tension arm for any wear or damage. If any, replace them with new ones.


Hide 11101A 7.INSPECT CYLINDER HEAD SET BOLT

A137166C03
2.354,0.542 2.708,0.844 0.354,0.302 10 *b 1.802,0.542 2.146,0.865 0.344,0.323 10 *a
*a 25 mm (0.9843 in.)
*b 20 mm (0.7874 in.)


a.

Using a micrometer, measure the thread diameter at several positions as indicated in the illustration.

Minimum bolt diameter:

8.75 mm (0.3445 in.)


If the thread diameter is less than the minimum, replace the cylinder head set bolt.


Hide 8.INSPECT CAMSHAFT

A137181

a.

Inspect the circle runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the concentricity of the camshaft at the center journal.

Maximum circle runout:

0.03 mm (0.0012 in.)


If the circle runout is greater than the maximum, replace the camshaft.



b.
A137182

Inspect the cam lobe height.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:
Camshaft:

40.38 to 40.52 mm (1.5898 to 1.5953 in.)

No. 2 Camshaft:

39.89 to 40.03 mm (1.5705 to 1.5760 in.)


If the cam lobe height is not as specified, replace the camshaft.



c.
A137183

Inspect the cam journal diameter.

i.

Using a micrometer, measure the cam journal diameter.

Standard journals diameter:
Camshaft No. 2 Camshaft
No. 1 journal 33.984 to 34.000 mm
(1.3380 to 1.3386 in.)
25.979 to 25.995 mm
(1.0228 to 1.0234 in.)
No. 2 - No. 5 journal 22.979 to 22.995 mm
(0.9047 to 0.9053 in.)
22.979 to 22.995 mm
(0.9047 to 0.9053 in.)

If the cam journal diameter is not as specified, inspect the oil clearance.



Hide 9.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Set the No. 2 camshaft and camshaft to the cylinder head.


b.
A137184

Using a dial indicator, measure the thrust clearance of each camshaft (while moving the camshaft back and forth).

Standard thrust clearance:

0.10 to 0.24 mm (0.0039 to 0.0095 in.)


If the thrust clearance is not as specified, replace the cylinder head. If the thrust of the camshaft is scratched, replace the camshaft, as well.


Hide 10.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft and bearing cap.


b.

Set the camshaft on the cylinder head.


c.
A137185

Lay a strip of Plastigage across the camshaft journal.


d.

Install the camshaft bearing cap.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not turn the camshaft when measuring.



e.

Remove the bearing cap.


f.
A137186

Measure the Plastigage at its widest point.

Standard oil clearance:
Camshaft Camshaft No. 2
No. 1 journal 0.025 to 0.061 mm
(0.0010 to 0.0024 in.)
0.037 to 0.073 mm
(0.0015 to 0.0029 in.)
No. 2 - No. 5 journal 0.037 to 0.073 mm
(0.0015 to 0.0029 in.)
0.037 to 0.073 mm
(0.0015 to 0.0029 in.)

Maximum oil clearance:

0.10 mm (0.0039 in.)


If the width is greater than the maximum, replace the cylinder head.

NOTICE:

Completely remove the Plastigage after the measurement.