Home › Engine / Hybrid System › K3-VE FUEL › FUEL SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002972 K3-VE FUEL _0015020 FUEL SYSTEM G

K3-VE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL PRESSURE

a.

Take precautions to prevent gasoline spillage (See page Engine / Hybrid System>K3-VE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Measure the battery voltage.

Standard voltage:

11 to 14 V



c.

Disconnect the cable from the negative battery terminal.


d.
A126541C06
2.927,0.885 2.458,0.521 false 0.74,1.375 0.417,2.5 true 1.26,2.438 1.198,2.813 false 1.542,2.396 1.938,2.844 false 2.188,2.188 2.417,2.188 false 2.167,0.344 2.719,0.656 0.552,0.313 10 SST *1 2.448,2.104 3.104,2.458 0.656,0.354 10 SST *2 1.969,2.854 2.573,3.125 0.604,0.271 10 SST *3 0.906,2.854 1.5,3.135 0.594,0.281 10 SST *4 0.333,2.531 0.635,2.854 0.302,0.323 10 *5
*1 Pressure Gauge
*2 Hose
*3 T-joint
*4 Fuel Hose
*5 Pulsation Damper


Disconnect the fuel hose from the pulsation damper, then install SST.

SST
09268-31011  (09268-41120, 95336-08070)
09268-45014  (09268-41200, 09268-41220, 90467-13001)


e.

Wipe off any spilt gasoline.


f.

Connect the cable to the negative battery terminal.

Torque:
6.4 N*m (65 kgf*cm, 56 in.*lbf)


g.

Actuate the fuel pump (see step 2. CHECK FUEL PUMP OPERATION).


h.

Measure the fuel pressure.

Fuel pressure:

319 k to 329 kPa (3.3 to 3.4 kgf/cm2, 46 to 48 psi)


·

If the fuel pressure is greater than the standard value, replace the fuel pump.

·

If the fuel pressure is less than the standard value, check the fuel hoses, connections of the fuel hoses, fuel pump, fuel filter and fuel pressure regulator.



i.

Install the F/P relay.


j.

After measuring the fuel pressure, disconnect the cable from the negative battery terminal. Remove SST while being careful to prevent gasoline splashes.


k.

Connect the fuel hose to the pulsation damper.


Hide 2.CHECK FUEL PUMP OPERATION

a.

Remove the F/P relay from the fuse block (See page Engine / Hybrid System>K3-VE FUEL>FUEL SYSTEM>PRECAUTION).


b.
A261188C04
0.141,0.062 0.327,0.224 0.186,0.161 10 *1
*1 Fuse Block


Using a service wire, connect terminals 3 and 5 of the fuse block.

NOTICE:

Be sure not to connect the wrong terminals. It may cause a malfunction.



c.

Turn the ignition switch to ON, and check that the fuel pump operates.

NOTICE:

Do not start the engine.



d.
A261189C06
0.948,0.354 0.458,0.198 true 0.281,0.115 0.563,0.375 0.281,0.26 10 *1
*1 Screw


Check that the pulsation damper screw is pushed up by operating the fuel pump.

If not, check the following parts.

·

Fusible link

·

Fuses

·

EFI relay

·

F/P relay

·

Fuel pump

·

ECM

·

Wiring connections



e.

Turn the ignition switch off.


f.

Install the F/P relay to the fuse block (See page Engine / Hybrid System>K3-VE FUEL>FUEL SYSTEM>PRECAUTION).