Home › Engine / Hybrid System › K3-VE FUEL › FUEL INJECTOR › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002972 K3-VE FUEL _0015021 FUEL INJECTOR G

K3-VE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

A154756C07
2.813,0.229 2.958,0.375 0.146,0.146 10 *1 0.042,0.021 0.302,0.219 0.26,0.198 10 *a
*1 Ohmmeter
*a Component without harness connected
(Fuel Injector Assembly)


a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68 °F) 11.6 to 12.4 Ω


If the resistance is not as specified, replace the fuel injector.

NOTICE:

After replacing the injector assembly, perform the "inspection after repairs"




b.

Check the operation.

NOTICE:

Perform the inspection in a well-ventilated area. Do not perform the inspection near any flames.


i.
A276021C02
1.698,0.896 2.167,1.229 false 2.073,2.927 2.521,3.365 true 1.948,3.771 2.031,4.115 2.031,4.115 2.115,3.771 true 1.469,0.76 1.677,0.948 0.208,0.188 10 *1 1.979,4.219 2.188,4.406 0.208,0.188 10 *3 1.865,2.75 2.073,2.938 0.208,0.188 10 *2
*1 Fuel Pipe
*2 Retainer
*3 O-ring


SST (connector) seals the fuel tube connector and pipe with an O-ring.

SST
09268-31013  (09268-41110, 09268-41130, 95336-08070)


ii.

Ensure that there is no damage or foreign matter on the contact surface.


iii.
A126544C04
0.646,0.958 1.26,0.958 false 1.396,0.542 2.135,0.542 false 2.469,1.469 2.677,1.469 false 0.656,0.302 1.229,0.302 false 0.635,2.021 1.26,2.021 false 2.167,0.469 2.344,0.625 0.177,0.156 10 *5 0.458,0.885 0.646,1.042 0.188,0.156 10 *1 0.458,0.24 0.646,0.396 0.188,0.156 10 *4 0.448,1.958 0.635,2.115 0.188,0.156 10 *2 2.708,1.406 2.885,1.563 0.177,0.156 10 *3
*1 O-ring
*2 Vinyl tube
*3 SST (Clamp)
*4 SST (Clip)
*5 SST (Adapter)


Install the O-ring onto the fuel injector.


iv.

Connect SST (fuel tube connector) to SST (hose), and then connect them to the fuel pipe (vehicle side).


v.

Install a new O-ring onto the fuel injector.


vi.

Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).


vii.

Connect SST (a hose) to No. 1 fuel pipe.


viii.
A147390N06
1.769,0.777 2.063,0.924 0.295,0.147 10 SST 1.7,0.404 1.896,0.777 false

Set the fuel injector in a graduated cylinder.


ix.

Actuate the fuel pump.


x.

Install SST onto the fuel injector.

SST
09843-97201  


xi.

Connect SST onto the battery, and measure the injection volume for 15 seconds. Perform the inspection 2 or 3 times, then calculate the average.

Standard volume:
Injection Volume Difference between fuel injectors
47 to 58 cm3 (2.9 to 3.5 cu in.) per 15 sec. 11 cm3 (0.7 cu in.) or less


NOTICE:

Always do the switching on the battery side.


If the result is not as specified, replace the fuel injector.



c.
A116184

Check the leakage.

i.

If inspecting the injection volume, remove SST from the battery. Inspect the fuel leakage from the injector.

Standard:

1 drop or less every minute


If the result is not as specified, replace the fuel injector.