Home › Engine / Hybrid System › 3SZ-VE COOLING › COOLANT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002978 3SZ-VE COOLING _0015053 COOLANT A

3SZ-VE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

CAUTION:

To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


a.

Loosen the radiator drain cock plug.


b.

Remove the radiator cap sub-assembly.


c.

Loosen the drain cock plug, then drain the coolant.

A261335C02
2.031,2.073 2.031,1.49 2.031,1.49 2.219,1.49 false 3.583,1.563 3.583,0.979 3.583,0.979 3.396,0.979 false 2.667,5.083 3.156,5.083 false 5.635,2.969 5.635,4.74 5.635,4.74 5.438,4.74 true 3.219,0.906 3.906,1.385 0.688,0.479 10 *1 2.25,1.417 3.188,2.052 0.938,0.635 10 *3 3.177,5.021 3.667,5.385 0.49,0.365 10 *4 5.26,4.667 5.958,5.271 0.698,0.604 10 *2
*1 Air-Bleeding Valve *2 Drain Cock Plug
*3 Radiator Cap Sub-assembly *4 Radiator Drain Cock Plug



Hide 2.ADD ENGINE COOLANT

HINT:
·

Improper coolant may damage the engine cooling system.

·

Use only "Toyota Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of the combination of low phosphates and organic acids).

·

New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant is recommended.



NOTICE:

Do not use alcohol-based antifreeze or plain water alone.


a.

Tighten all drain cock plugs.


b.
A261337C01
0.51,1.073 0.333,0.813 true 0.125,0.688 0.542,1.063 0.417,0.375 10 *1
*1 Air-Bleeding Valve


Loosen and remove air-bleeding valve.


c.

Fill the radiator with coolant from the fill port.

NOTICE:
·

Deionized water or distilled water is recommended to be used when diluting the coolant.

·

Do not use a tap water.




d.

Tighten air-bleeding valve when the coolant overflows from valve.

NOTICE:
·

Cover the generator located under the air bleeder cock with a piece of cloth so the generator does not get wet with the coolant.

·

If the coolant does not overflow from either of the valves, during steps (e) through (f), tighten the valves after the coolant overflows from the radiator.




e.

Install the radiator cap when the coolant overflows from the radiator.

HINT:

Observe the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.



f.

Fill the radiator reservoir tank with coolant up to the full level.


g.

Start the engine and keep the engine speed at 2000 rpm. Warm up the engine until the cooling fan operates twice.

HINT:

When warming up the engine, squeeze the radiator inlet hose and outlet hose a few times.



h.

Stop the engine, then wait until the coolant cools down. Remove the radiator cap and check the coolant level.


i.

If the coolant level goes down, repeat steps (b) through (i).


j.

When the coolant level stops going down, adjust the amount of the coolant in the radiator reservoir tank.

Capacity:

6.8 liters (7.2 US qts, 6.0 lmp. qts) for Automatic Transaxle

7.0 liters (7.4 US qts, 6.2 lmp. qts) for Manual Transmission