Home › Engine / Hybrid System › K3-VE STARTING › STARTER(for Manual Transmission) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002982 K3-VE STARTING _0015076 STARTER(for Manual Transmission) A

K3-VE STARTING  STARTER(for Manual Transmission)  REASSEMBLY  


PROCEDURE

Hide 28199A 1.INSTALL DUST STARTER PROTECTOR

Hide 28011 2.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.

Apply grease to the starter clutch sub-assembly bushing, spline and starter pinion stop nut (inner).


b.
A261432

Install the starter clutch sub-assembly and starter pinion stop nut (inner) onto the starter armature assembly.


c.

Apply grease to a new snap ring, then install it onto the starter armature assembly groove.


d.
A142266C04
0.979,1.698 1.073,1.698 1.073,1.698 1.073,1.802 true 0.99,1.823 1.448,2.177 0.458,0.354 10 *1
*1 Snap Ring


Compress the snap ring using a vise.


e.
A262948C04
2.146,0.583 2.24,0.583 false 2.031,0.667 1.958,0.802 true 1.813,0.833 2.302,1.125 0.49,0.292 10 *1 2.271,0.521 2.677,0.833 0.406,0.313 10 *2
*1 Snap Ring
*2 Starter Pinion Stop Nut (inner)


While holding the starter clutch sub-assembly by hand, slightly tap the starter armature assembly shaft tip with a plastic faced hammer until the starter pinion stop nut (inner) fits over the snap ring.


f.

Install the starter pinion stop nut (outer).


Hide 28120 3.INSTALL STARTER YOKE ASSEMBLY

a.

Clamp the starter armature assembly shaft in a vise.

NOTICE:

Do not clamp it in a vise too tightly.



b.

Install the starter yoke assembly onto the starter armature assembly.


c.
A142268

Install the starter brush holder assembly.


d.
A142269

Install the 4 brush springs.

NOTICE:

Do not allow the brush springs to fly off.



e.
A142270

Install the brush holder insulator.


f.

Install the starter commutator end flame assembly.


g.
A262949C04
3.208,2.115 3.354,2.115 false
V100135

Grease


Apply grease to the contact surfaces of the starter pinion drive lever, housing, clutch and plunger.


h.
A142241

Install the starter yoke assembly and starter pinion drive lever onto the starter drive housing with the 2 through bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 28150 4.INSTALL MAGNET STARTER SWITCH ASSEMBLY

A142240C08
2.292,0.573 2.917,0.573 true 1.719,0.604 1.719,0.198 1.719,0.198 1.323,0.198 false 1.125,0.125 1.594,0.458 0.469,0.333 10 *1 2.979,0.5 3.385,0.854 0.406,0.354 10 *2
*1 Plunger
*2 Magnet Starter Switch Assembly


a.

Place the plunger in place on the starter pinion drive lever, then install the magnet starter switch assembly.


b.
A142239

Install the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 74 in.*lbf)


c.
A142238

Install the lead wire onto the magnet starter switch assembly terminal with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)